Allied Telesis AT-SBX81XS6 Instalační příručka Strana 138
- Strana / 314
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 7: Installing the AT-SBx81CFC960 Control Card and Ethernet Line Cards
138 Section II: Installing the Chassis
Installing the Blank Slot Covers
After installing the AT-SBx81CFC960 Controller Fabric Cards and
Ethernet line cards, check the front panel for unused slots and cover them
with the blank slot covers included with the chassis, as explained in this
procedure. The fan module may not be able to maintain adequate airflow
across the control and line cards if the chassis is not completely enclosed.
If there are no unused slots, go to Chapter 8, “Installing the Transceivers
and Cabling the Ports” on page 141.
To install the blank panels on the unused slots, perform the following
procedure:
1. Position a blank slot cover over an unused slot, as shown in Figure 76.
The up arrow on the panel must be pointing up.
Figure 76. Installing a Blank Slot Cover
2. Finger tighten the two thumbscrews to attach the blank panel to the
chassis, as shown in Figure 77.
Figure 77. Tightening the Thumbscrews on a Blank Slot Cover
3. Tighten the two screws with a # 2 Phillips-head screwdriver to secure
the blank slot cover to the chassis.
Up Arrow
- Installation Guide 1
- Radiated Energy 3
- Industry Canada 3
- Translated Safety Statements 4
- Contents 5
- List of Tables 14
- ™ feature 16
- Contacting Allied Telesis 18
- Hardware Overview 19
- Chassis and Power Supplies 21
- Introduction 22
- AT-SBx8112 Chassis 24
- Slots for the Power Supplies 27
- AT-SBxPWRSYS1 Power Supply 28
- AT-SBxPWRPOE1 Power Supply 30
- AT-SBxPWRSYS1 DC Power Supply 32
- AT-SBxFAN12 Module 34
- AT-SBx81GT24 Line Card 39
- AT-SBx81GT40 Line Card 41
- AT-SBx81GP24 PoE Line Card 44
- AT-SBx81GS24a SFP Line Card 47
- AT-SBx81XS6 SFP+ Line Card 49
- Distance 52
- Requirements 52
- Detection 53
- Automatic MDIX 53
- Powered Device 54
- Chapter 3 57
- Hardware Components 58
- Guidelines 60
- Dual Controller Cards 62
- SYS Status LEDs 64
- SBx Linecard Status LEDs 67
- SFP+ Slots 68
- Console (RS-232) Port 70
- NET MGMT Port 71
- NET MGMT 72
- USB Port 74
- Reset Button 75
- Installing the Chassis 79
- Safety Precautions and Site 81
- Reviewing Safety Precautions 82
- Chapter 5 89
- Required Tools and Material 90
- Preparing the Equipment Rack 91
- Removing the Shipping Brace 101
- Installing the Power Supplies 105
- Card and Ethernet Line Cards 125
- INCORRECT 127
- Controller Fabric Card 132
- Chapter 8 141
- Cables to the AT 143
- SBx81GT40 Line 143
- Connecting 143
- Powering On the Chassis 163
- Verifying the Installation 164
- Connecting the 176
- Grounding Wire 176
- DC Power Wires 187
- Angle Terminals 187
- Connecting Bare 193
- Chapter 10 201
- Starting a Local 204
- Management 204
- Entering the 205
- AlliedWare Plus 205
- Operating System 205
- Commands 205
- Troubleshooting 207
- Chapter 11: Troubleshooting 210
- Ethernet Line Cards 211
- Twisted Pair Ports 212
- Power Over Ethernet 214
- AT-SBxFAN12 Fan Module 218
- Replacing Modules 221
- Supplies 222
- Chapter 12: Replacing Modules 224
- Figure 144 on page 226 225
- 152 on page 234 233
- Figure 155 on page 237 236
- Replacing Ethernet Line Cards 238
- Removing the 243
- AT-SBxFAN12 243
- Fan Module 243
- Connector 245
- Installing a New 247
- Chapter 13 251
- Before You Begin 252
- Switches 257
- Section III 259
- VCStack Plus Overview 261
- Overview 262
- One Controller 265
- Card Per Chassis 265
- Two Controller 266
- Cards Per 266
- VCStack Plus Feature License 268
- Optional Feature Licenses 269
- Chassis ID Numbers 270
- Priority Numbers 271
- Stacking Guidelines 273
- Building a Stack 275
- Chapter 15: Building a Stack 278
- Enabling the Stacking Feature 281
- Setting the ID Number 285
- Setting the Priority Number 289
- Powering Off the Chassis 290
- Powering On the Stack 295
- Powering On the 296
- Monitoring the 296
- Sequence 296
- Verifying the Stack 299
- Troubleshooting the Stack 302
- Technical Specifications 305
- Environmental Specifications 307
- Power Specifications 308
- PoE Mode 310
- Port Pinouts 311
- Transceivers 313
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce