Allied Telesis Rapier 16Fi-FX Instalační příručka Strana 173
- Strana / 283
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
IP Multicasting set pim log 79
The suppressiontime parameter specifies the register suppression time. This
determines the interval at which the sender’s DR sends null register messages
to the group’s RP to tell it to send another register stop message if it still does
not need the data to be registered and sent to it. The default is 60 seconds. This
timer applies to PIM-SM only.
Examples To set the join/prune message interval to 90 seconds, use the command:
set pim jpi=90
Related Commands enable pim
set pim interface
show pim
show pim bsrcandidate
show pim counters
show pim debug
show pim interface
show pim neighbour
show pim route
show pim rpcandidate
show pim rpset
show pim timer
set pim log
Syntax SET PIM LOG=[NONE|STAtus|ERRor|ALL] [TRap=[NONE|STAtus|
ERRor|ALL]]
Description This command applies to PIM-SM only and sets the type of logging for status
PIM log messages, error messages and/or sending of SNMP traps for certain
error conditions.
The log parameter specifies whether status, error, or all log messages should
be generated. The default is status.
The trap parameter specifies whether status, error, or all traps should be
generated.
Related Commands show pim debug
- Software Version 2.9.1 1
- 2 Release Note 2
- Release Licences 5
- Upgrading the GUI File 5
- Backwards Compatibility 6
- Overview of New Features 7
- AT-8624POE Fan Enhancements 9
- C613-10486-00 REV C 10
- VPN Configuration Wizards 11
- Command Changes 12
- System Enhancements 13
- Command Reference Updates 14
- Switching Enhancements 18
- PoE Firmware Upgrade 20
- SHDSL Enhancements 23
- Bridging Enhancements 26
- Software Version 2.9.1 27 27
- Training VLAN VID=2 28
- PPP Link 28
- Software Version 2.9.1 31 31
- Syntax SHow BRIDge 32
- Dynamic DNS Client 33
- Within a Subnet 34
- IP Debug Timeout 35
- Software Version 2.9.1 37 37
- Software Version 2.9.1 41 41
- Syntax SHow DDNS 42
- DHCP Enhancements 45
- DHCP Snooping Enhancements 50
- IP Multicasting Enhancements 55
- OSPF Enhancements 59
- BGP Enhancements 61
- IPv6 Enhancements 63
- ■ all static routes 64
- ■ all interface routes 64
- Firewall Enhancements 65
- Software Version 2.9.1 75 75
- ALG, use the command: 86
- Associations 88
- Changes to Local Commands 94
- IP Multicasting 95
- IP Multicasting 3 97
- IP Multicast Routing 98
- IP Multicasting 5 99
- PIM Dense Mode 100
- Configuring PIM Dense Mode 101
- General PIM-DM 102
- IP Multicasting 9 103
- PIM Sparse Mode 103
- 10 Software Reference 104
- Rendezvous point 105
- IP Multicasting 11 105
- 12 Software Reference 106
- Configuring PIM Sparse Mode 107
- Bootstrap router 108
- General PIM-SM 109
- IP Multicasting 17 111
- Configuring IGMP 112
- Static IGMP 113
- IGMP Proxy 114
- IGMP Snooping 116
- Downstream routers 117
- Fast Leave 118
- Query Solicitation 118
- IP Multicasting 25 119
- IGMP Filtering 120
- IGMP Throttling 122
- IP Multicasting 29 123
- Dynamic MVR 123
- Compatible MVR 123
- Immediate Leave 124
- Configuring MVR 124
- Configuration Examples 125
- Switch B 126
- Switch A 126
- Switch C 126
- Command Reference 134
- IP Multicasting enable pim 69 163
- [interface=vlan] 167
- ■ DVMRP Routers, 224.0.0.4 168
- ■ All PIM routers, 224.0.0.13 168
- ■ IGMP is enabled globally 170
- ■ the interface is active 170
- IP Multicasting set ip mvr 77 171
- 78 set pim Software Reference 172
- Syntax SHow IP IGMP DEBug 191
- Syntax SHow PIM COUnters 197
- Table 11 on page 104) 197
- Syntax SHow PIM INTerface 202
- VLAN (such as vlan1, vlan1-1) 202
- Syntax SHow PIM ROUte 205
- Syntax SHow PIM RPSet 212
- Introduction 217
- Link Layer Discovery Protocol 217
- Type Length Values 218
- Transmission and Reception 219
- Transmission 220
- Reception 220
- Storing LLDP Information 221
- Configuring LLDP 223
- Monitoring LLDP 224
- LLDP Triggers 225
- 802.1AB-2005 251
- LLDP neighbours is displayed 255
- MAC-Forced Forwarding 259
- 2 Software Reference 260
- MAC-Forced 261
- Forwarding with 261
- DHCP snooping 261
- Isolating clients using VLANs 262
- Manually adding 263
- ■ ARP packets 264
- Debugging 265
- Logging 265
- 8 Software Reference 266
- See Also show macff interface 277
- Syntax SHOW MACFF DATABase 278
Související produkty a manuály pro Síťové přepínače Allied Telesis Rapier 16Fi-FX
(51 stránky)
Síťové přepínače Allied Telesis 86241-06 Specifikace
(30 stránky)
(30 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce