Allied-telesis OmniConnect ISDN Uživatelský manuál Strana 13
- Strana / 91
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
OmniConnect / ISDN User’s Manual Page 7
Part number 613-10787-00
2.4.1. Power (green)
When ON, the OmniConnect/ISDN is connected to the 12V DC power source.
OmniConnect/ISDN is powered when it is plugged in, there is no power switch.
2.4.2. Collision (amber)
When FLASHING, the OmniConnect/ISDN is experiencing collisions on the LAN segment to
which it is attached. It is normal for this indicator to flash on occasion.
2.4.3. Link (green)
This LED provides information about the state of the Ethernet 10Base-T connection. There
are four LEDs, one for each of the ports (1-4).
LED State Condition
OFF The port is not connected to an active 10Base-T repeater or adapter
FLASHING The port is receiving data on the associated port
ON The port is connected to an active 10Base-T repeater or adapter and the link
active
2.4.4. B1 channel (green)
This LED provides information about the state of the ISDN connection. There is a single LED
for each of the B1, B2 and D channels.
LED State Condition
OFF The B1 channel is not active
FLASHING The port is receiving and transmitting data on the B1 channel
ON The port is connected to an ISDN switch
2.4.5. B2 channel (green)
This LED provides information about the state of the ISDN connection. There is a single LED
for each of the B1, B2 and D channels.
LED State Condition
OFF The B2 channel is not active
FLASHING The port is receiving and transmitting data on the B2 channel
ON The port is connected to an ISDN switch
2.4.6. D channel (green)
This LED provides information about the state of the ISDN connection. There is a single LED
for each of the B1, B2 and D channels.
LED State Condition
OFF The D channel is not active
FLASHING The port is connecting to an ISDN switch and the Terminal Endpoint
Identifier is being assigned.
ON The port is connected to an ISDN switch
- Internet Access Device 1
- Limited Warranty 2
- TABLE OF CONTENTS 3
- 1. About This Guide 7
- 1.4. Document Conventions 8
- 2. Introduction and Overview 9
- 2.1.5. Advanced voice support 10
- 2.1.6. Dial-on-demand routing 10
- User’s Manual Page 5 11
- Part number 613-10787-00 11
- 2.2. Security features 12
- 2.3. Supported RFCs 12
- 2.4. OmniConnect/ISDN panels 12
- User’s Manual Page 7 13
- User’s Manual Page 8 14
- User’s Manual Page 9 15
- 3. Preparing for Installation 16
- 3.2. Helpful information 17
- User’s Manual Page 12 18
- User’s Manual Page 13 19
- 3.5.2. ISDN switch types 20
- User’s Manual Page 15 21
- User’s Manual Page 16 22
- User’s Manual Page 17 23
- User’s Manual Page 18 24
- Release Key 24
- Notification Busy Limit 24
- 3.6. SPIDs 25
- User’s Manual Page 20 26
- User’s Manual Page 21 27
- User’s Manual Page 22 28
- 3.7. Cabling specifications 29
- Pin(s) Function 30
- 1, 2, 5, 6, 7, 8 Not Used 30
- 3 Tip Connection 30
- 4 Ring Connection 30
- 4. Getting Started 31
- User’s Manual Page 26 32
- User’s Manual Page 27 33
- 4.4.3.1. New installations 34
- User’s Manual Page 29 35
- 4.6. Power supply connection 36
- 5. Configuration and Setup 37
- 5.3. OmniStart configuration 38
- 5.4. OmniStart screens 38
- User’s Manual Page 33 39
- 5.4.3. Multiple router setup 40
- 5.4.4. Enter password 40
- 5.4.6. ISDN parameters setup 41
- User’s Manual Page 36 42
- User’s Manual Page 37 43
- User’s Manual Page 38 44
- 5.4.9. ISDN Add phone number 45
- User’s Manual Page 40 46
- 5.4.12. ISDN Directory setup 47
- 5.4.13. ISDN Add phone number 48
- 5.4.15. ISDN Remove phone 49
- 5.4.16. DNS configuration 50
- User’s Manual Page 45 51
- 6. Advanced Setup Options 52
- 6.3. Advanced setup screens 53
- 6.3.3. Route information 54
- 6.3.4. Setup Internet filter 55
- 6.3.5. Advanced filter setup 56
- User’s Manual Page 51 57
- User’s Manual Page 52 58
- 6.3.6. OmniNAT setup 59
- 6.3.7. Static NAT entries 59
- 6.3.8. Static PAT entries 60
- User’s Manual Page 55 61
- 6.3.10. LAN IP configuration 62
- User’s Manual Page 57 63
- User’s Manual Page 58 64
- User’s Manual Page 59 65
- 6.3.14. WAN IP address setup 66
- 7. OmniConnect Monitor 67
- User’s Manual Page 62 68
- 7.4.2. Select OmniConnect 69
- 7.4.3. Configure duration 69
- 7.4.4. Caller ID 69
- 7.4.5. Phone extension 70
- 7.4.6. Diagnostics 70
- 7.4.7. Firmware upgrade 71
- 8. Troubleshooting 72
- User’s Manual Page 67 73
- 8.2. Software 74
- User’s Manual Page 69 75
- 8.3. ISDN cause codes 76
- User’s Manual Page 71 77
- User’s Manual Page 72 78
- User’s Manual Page 73 79
- User’s Manual Page 74 80
- Appendix A. Glossary 81
- User’s Manual Page 76 82
- User’s Manual Page 77 83
- User’s Manual Page 78 84
- Appendix B. Regulatory 85
- B.3. EMC information 86
- B.3.1. EN55022B statement 86
- B.3.2. FCC Class B statement 86
- B.4. FCC Part 68 statement 87
- User’s Manual Page 82 88
- User’s Manual Page 83 89
- Appendix C. Common TCP/UDP 90
- User’s Manual Page 85 91
Související produkty a manuály pro Počítačový hardware Allied-telesis OmniConnect ISDN
(95 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce