Allied-telesis AT-S62 Uživatelský manuál Strana 284
- Strana / 335
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 22: GARP VLAN Registration Protocol
Section V: Virtual LANs 284
Join Time
Sets the duration of the Join Period timer. The range is from 10 to
60 centiseconds and the default is 20.
If you change this timer, it must in relation to the GVRP Leave
Timer according to the following equation:
Join Timer <= 2 x (GVRP Leave Timer)
Enable GIP
Enables the operation of GIP. If enabled, attribute registrations
and de-registrations processed on a port are propagated to other
ports in the GIP-connected ring. GIP must be enabled in order to
use GVRP.
Note
Do not disable GIP if you intend to use GVRP. GIP is required to
propagate VLAN information among the ports of the switch.
Leave All Time
Sets the duration of the LeaveAll Period timer. The range is from
500 to 3000 centiseconds and the default is 1000.
Caution
The settings for the three GVRP timers must be the same on all
GVRP-active devices in your network.
5. Click Apply.
The new GVRP settings are activated on the switch.
6. To permanently save the changes, select the Save Config menu
selection.
- Web Browser Interface 1
- User’s Guide 1
- Table of Contents 3
- Section II 4
- Advanced Operations 4
- Section III 6
- Section VII 8
- List of Figures 10
- How This Guide is Organized 13
- Document Conventions 15
- Contacting Allied Telesyn 17
- Basic Operations 18
- Chapter 1 19
- Switch’s IP Address 20
- Saving Your Parameter Changes 23
- Enhanced Stacking 25
- Chapter 2: Enhanced Stacking 26
- Returning to the 29
- Master Switch 29
- Basic Switch Parameters 31
- Displaying System Information 37
- Rebooting a Switch 40
- Setting the System Time 41
- Pinging a Remote System 44
- SNMPv1 and SNMPv2c Community 47
- Changes on page 23 49
- Modifying a Community String 53
- Deleting a Community String 55
- Port Parameters 57
- Configuring Port Parameters 58
- Chapter 5: Port Parameters 60
- MAC Address Table 68
- Chapter 6:MAC Address Table 70
- Changing the Aging Time 76
- Static Port Trunks 77
- Creating a Static Port Trunk 78
- Chapter 7: Static Port Trunks 80
- Creating a Port Mirror 86
- Chapter 8: Port Mirroring 88
- Deleting a Port Mirror 90
- Displaying the Port Mirror 91
- File System 93
- Chapter 9: File System 94
- Downloading a File 98
- Uploading a File 101
- Event Log and Syslog Servers 103
- Managing the Event Log 104
- Displaying the 106
- Event Log 106
- Event Log Full 110
- Modifying the 110
- Saving the Event 111
- Clearing the 111
- Creating a Syslog 113
- Server Definition 113
- Modifying a 117
- Syslog Server 117
- Definition 117
- Deleting a Syslog 117
- Viewing a Syslog 118
- Classifiers 119
- Chapter 12: Classifiers 122
- Modifying a Classifier 126
- Deleting a Classifier 127
- Displaying the Classifiers 128
- Access Control Lists 129
- Quality of Service 137
- Managing Flow Groups 138
- Modifying a Flow 140
- Deleting a Flow 142
- Displaying Flow 142
- Managing Traffic Classes 144
- Traffic Class 148
- Deleting a Traffic 149
- Traffic Classes 150
- Managing Policies 151
- Displaying 155
- Policies 155
- Class of Service 156
- Configuring CoS 157
- Chapter 15: Class of Service 158
- Displaying the CoS Settings 162
- IGMP Snooping 164
- Configuring IGMP Snooping 165
- Chapter 16: IGMP Snooping 166
- Denial of Service Defense 170
- Displaying the DoS Settings 174
- Power Over Ethernet 175
- Setting the PoE Threshold 176
- Configuring PoE Port Settings 178
- SNMPv3 Operations 183
- SNMPv3 Protocol 184
- Enabling the SNMP Protocol 186
- Creating a User 188
- Table Entry 188
- Chapter 19: SNMPv3 Protocol 190
- 1.3.6.1.2.1.6 196
- Deleting a View 198
- Modifying a View 199
- Deleting an 204
- Access Table 204
- Modifying an 206
- Creating a 208
- SecurityToGroup 208
- Deleting a 210
- Notify Table 216
- Creating a Target 218
- Address Table 218
- Modifying Target 222
- Parameters Table 224
- Community 234
- Displaying User 238
- Table Entries 238
- Displaying View 239
- Displaying Notify 242
- Displaying Target 243
- Spanning Tree Protocols 246
- STP, RSTP, and MSTP 247
- Configuring STP 249
- Configuring RSTP 254
- Configuring MSTP 258
- Associating 261
- VLANs to MSTIs 261
- Configuring 264
- MSTP Port 264
- Parameters 264
- Virtual LANs 269
- Section V: Virtual LANs 271 271
- Section V: Virtual LANs 273 273
- Section V: Virtual LANs 275 275
- Section V: Virtual LANs 277 277
- Selecting a VLAN Mode 279
- Section V: Virtual LANs 281 281
- Configuring GVRP 283
- Section V: Virtual LANs 284 284
- Displaying the GVRP Settings 286
- Protected Ports VLANs 287
- Section V: Virtual LANs 288 288
- Port Security 290
- MAC Address Security 291
- Section VI: Port Security 292 292
- Section VI: Port Security 294 294
- Section VI: Port Security 296 296
- Section VI: Port Security 298 298
- Section VI: Port Security 301 301
- Section VI: Port Security 303 303
- Section VI: Port Security 305 305
- Section VI: Port Security 307 307
- Management Security 309
- Encryption Keys, PKI, and SSL 310
- Displaying Encryption Keys 311
- Displaying the SSL Settings 315
- Secure Shell Protocol 316
- Configuring the SSH Server 317
- Displaying SSH Information 319
- RADIUS and TACACS+ 320
- Authentication Protocols 320
- Chapter 29 326
- Creating a Management ACL 327
- Adding or Deleting an ACE 329
- Displaying the Management ACL 330
Související produkty a manuály pro Počítačový hardware Allied-telesis AT-S62
(2 stránky)
(40 stránky)
(38 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce