Allied-telesis AT-GS950/48 Uživatelský manuál Strana 332
- Strana / 378
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 27: Rebooting the AT-GS950/48
332
Configure Factory Default Values
The following procedure returns all AT-S116 Version 1.0.0 Management
software parameters to their factory default values and deletes all tagged
and port-based VLANs on the switch.
Note
The AT-S116 Version 1.0.0 Management software factory default
values are listed in “AT-GS950/8 Default Parameters” on page 347.
Caution
This procedure causes the switch to reboot. The switch does not
forward network traffic during the reboot process. Some network
traffic may be lost.
1. From the main menu on the left side of the page, select the Tools
folder.
The Tools folder expands.
2. From the Tools folder, select Reboot.
The Reboot Page is displayed. See Figure 132 on page 330.
3. Go to the lower part of the page to the Reboot section.
4. In the Reboot Type field, use the pull-down menu to select one of the
following options:
Normal - This setting reloads all configuration parameters that are
saved in flash memory. See “Switch Reboot” on page 330 for more
information when using this selection.
Factory Default - Resets all switch parameters to the factory
default settings, including the IP address, subnet mask, and
gateway address.
Caution
This setting will cause the IP address to be reset to 192.168.1.1.
You will loose connectivity with the switch management software
after the reboot is completed and you can login again with this IP
address.
Factory Default Except IP Address - Resets all switch parameters to
the factory default settings, but retains the current IP address, subnet
mask, and gateway settings saved in flash memory. If the DHCP client
is enabled, it remains enabled after this reset and assignment of the IP
- AT-GS950/48 1
- Contents 3
- List of Figures 9
- List of Tables 13
- Document Conventions 16
- Getting Started 19
- Chapter 1 21
- Switch’s IP Address 22
- Web Browser Tools 25
- System Configuration 27
- System Management Information 28
- IP Access List Configuration 32
- Delete an IP 33
- Address List 33
- Add New User 34
- Name and 34
- Password 34
- Modify User 35
- Delete User Name 36
- User Interface Configuration 37
- User Interface 38
- System Time 39
- Setting Daylight 41
- Parameters 41
- SSL Settings 42
- 4. Click Apply 43
- DHCP Client Configuration 45
- DHCP Auto Configuration 47
- System Information Display 48
- System Log Configuration 50
- Bridge Configuration 53
- Port Configuration 55
- Chapter 3: Port Configuration 58
- STP and RSTP 61
- Bridge Priority 63
- Path Costs and Port Costs 64
- Port Priority 64
- Forwarding 65
- Delay and 65
- Topology 65
- Point-to-Point and Edge Ports 66
- Mixed STP and 67
- RSTP Networks 67
- Spanning Tree 68
- Chapter 4: STP and RSTP 70
- Configure RSTP Port Settings 73
- Configure the 75
- Advanced RSTP 75
- Spanning Tree Topology 78
- Chapter 5 79
- VLAN Mapping 86
- Modify MST 87
- Instance 87
- Delete MST 87
- Topology Information 90
- Static Port Trunking 93
- Create a Port Trunk 97
- Modify a Port Trunk 99
- Disable a Port Trunk 101
- LACP Port Trunks 103
- Overview 104
- System Priority 105
- Port Priority Value 106
- General Guidelines 107
- Chapter 7: LACP Port Trunks 108
- Group Status 109
- Configuration 110
- Port Priority Configuration 112
- Port Mirroring 113
- Port Mirroring Configuration 115
- Disable Port Mirroring 116
- Loopback Protection 117
- MAC Address Table 121
- Chapter 10: MAC Address Table 124
- Modify Static Unicast Address 126
- Delete Static Unicast Address 127
- IGMP Snooping 133
- IGMP Snooping Configuration 136
- Chapter 11: IGMP Snooping 138
- Storm Control 139
- Ingress Rate 141
- Limiting 141
- Egress Rate 141
- Ingress Rate Limiting 144
- Egress Rate Limiting 146
- Virtual LANs 147
- VLAN Overview 148
- Port-based 149
- Tagged VLAN 150
- VLAN Index 151
- VLAN Name 151
- Tagged and Untagged Ports 151
- Port VLAN Identifier (PVID) 151
- General Rules for 152
- Creating a 152
- Assign Ports to a VLAN Mode 153
- Chapter 13: Virtual LANs 154
- Tagged VLAN Configuration 155
- Modify a Tagged 156
- Delete a Tagged 158
- Tagged VLAN Port Settings 160
- Port-Based VLAN Configuration 162
- Modify a Port 163
- Based VLAN 163
- Chapter 14 165
- Overview and Guidelines 166
- General Configuration 167
- Port Settings 168
- Time Settings 170
- Chapter 14: GVRP 172
- Chapter 15 173
- Egress Queue vs 175
- Packet Priority 175
- Prioritizing 176
- Untagged Packets 176
- Queue Scheduling Algorithm 183
- Advanced Features 185
- SNMPv1 and v2c 187
- SNMPv1 and SNMPv2c Overview 188
- Trap Receiver Attributes 189
- Activate SNMP Interface 190
- Create User and 191
- Group Names 191
- Modify User and 192
- Delete User and 193
- SNMP Community Strings 194
- SNMP Traps 196
- Modify a Trap 197
- Host Table Entry 197
- Delete a Trap 197
- Chapter 16: SNMPv1 and v2c 198
- Chapter 17 199
- SNMPv3 Privacy 201
- Protocol 201
- SNMPv3 MIB 201
- SNMPv3 User and Group Names 204
- Chapter 17: SNMPv3 206
- SNMPv3 View Names 207
- Modifying 209
- SNMPv3 View 209
- Deleting SNMPv3 209
- View Names 209
- SNMPv3 View Table 210
- SNMPv3 Traps 213
- Access Control Configuration 215
- Classifier 217
- Modifying a 219
- Deleting a 220
- Profile Action 222
- Modifying Profile 223
- Deleting a Profile 224
- In-Profile Action 225
- Modifying an In 227
- Deleting an In 228
- Out-Profile Action 229
- Modify Out 231
- Delete Out 232
- Port List 233
- “Create Policy,” next 236
- “Modify Policy” on page 238 236
- “Delete Policy” on page 239 236
- Policy Sequence Status 241
- Chapter 19 243
- Enable and Disable RMON 245
- Port Statistics 246
- Histories 248
- Chapter 19: RMON 250
- Voice VLAN 255
- Dynamic Auto 257
- Detection vs 257
- Static Ports 257
- Chapter 20: Voice VLAN 258
- OUI Setting 263
- Modify OUI 264
- Delete OUI 264
- Security 265
- Port Access Control 266
- Port Access 267
- Chapter 21: Security 268
- RADIUS Client 271
- Radius Client 272
- Dial-in User 274
- Modify a Dial-in User 275
- Delete a Dial-in User 276
- Destination MAC Filter 277
- Destination MAC 278
- Chapter 22 281
- DHCP Snooping 282
- DHCP with 284
- Option 82 284
- VLAN Setting 288
- Chapter 22: DHCP Snooping 290
- Binding Database 292
- Chapter 23 295
- Global Configuration 297
- Enabling or 298
- Disabling LLDP 298
- Displaying 299
- Information 299
- Setting Port 299
- Chapter 23: LLDP 300
- Neighbors Information 301
- Network Statistics 303
- Traffic Comparison Statistics 305
- Error Group Statistics 308
- Historical Status Charts 310
- Section IV 313
- Chapter 25 315
- File Upload 321
- File Download 323
- Cable Diagnostics 327
- Chapter 26: Cable Diagnostics 328
- Rebooting the AT-GS950/48 329
- Switch Reboot 330
- Disabling Factory 334
- Default Reset 334
- Enabling Factory 336
- Pinging a Remote System 339
- MSTP Overview 341
- Resolving VLAN 344
- Fragmentation 344
- Multiple VLANs 345
- Assigned to an 345
- Appendix A: MSTP Overview 346
- VLAN and MSTI Associations 348
- Ports in Multiple MSTIs 349
- MST Region 352
- Guidelines 352
- Associating VLANs to MSTIs 355
- Summary of Guidelines 359
- Appendix B 361
- Parameter 368
- Default Setting 368
- Specifications 368
Související produkty a manuály pro Počítačový hardware Allied-telesis AT-GS950/48
(550 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce