Allied-telesis SwitchBlade x3112 Uživatelský manuál

613-001297 Rev. FSwitchBlade x3112Access Edge Chassis Switch AT-SBx3112 Chassis AT-SBx31GT24 Line Card AT-SBx31GT40 Line Card AT-SBx31GP24 PoE Lin

List of Figures10Figure 46: Installing the Grounding Lug and Wire ...

Chapter 4: Installing the Power Supplies100Figure 54. Lowering the Handle on the AT-SBxPWRSYS1 AC Power Supply8. To install a second AT-SBxPWRSYS1 AC

SwitchBlade x3112 Installation Guide101Installing the AT-SBxPWRPOE1 AC Power SupplyThis section contains the installation procedure for the AT-SBxPWRP

Chapter 4: Installing the Power Supplies102Figure 56. Removing the Blank Slot Cover from Power Supply Slot A3. Remove the power supply from the shippi

SwitchBlade x3112 Installation Guide103Figure 57. Items Included with the AT-SBxPWRPOE1 Power Supply ModuleNoteStore the packaging material in a safe

Chapter 4: Installing the Power Supplies104Figure 58. Verifying the AT-SBxPWRPOE1 AC Power Supply5. Raise the locking handle on the AT-SBxPWRPOE1 AC P

SwitchBlade x3112 Installation Guide105Figure 60. Inserting the AT-SBxPWRPOE1 AC Power Supply

Chapter 4: Installing the Power Supplies1067. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

SwitchBlade x3112 Installation Guide107Installing the AT-SBxPWRSYS1 DC Power SupplyThis section contains the installation procedure for the AT-SBxPWRS

Chapter 4: Installing the Power Supplies108Figure 63. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the power supply from the shippi

SwitchBlade x3112 Installation Guide109Figure 64. Items Included with the AT-SBxPWRSYS1 DC Power Supply ModuleNoteStore the packaging material in a sa

SwitchBlade x3112 Installation Guide11Figure 101: Release Tab on the AT-SBx31XS6 Line Card ...

Chapter 4: Installing the Power Supplies110Figure 65. Loosening the Handle locking Screw on the AT-SBxPWRPOE1 DC Power Supply5. Raise the locking hand

SwitchBlade x3112 Installation Guide111Figure 67. Inserting the AT-SBxPWRSYS1 DC Power Supply

Chapter 4: Installing the Power Supplies1127. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

113Chapter 5Installing the AT-SBx31CFC Card and Ethernet Line CardsThis chapter describes how to install the control and Ethernet line cards. The chap

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards114Installing the AT-SBx31CFC Central Fabric Controller CardThis section contains th

SwitchBlade x3112 Installation Guide115Figure 70. Items Included with the AT-SBx31CFC Central Fabric Controller CardNoteStore the packaging material i

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards116Figure 72. Removing the Battery Insulator5. Align the edges of the AT-SBx31CFC Ma

SwitchBlade x3112 Installation Guide117Figure 74. Inserting the AT-SBx31CFC Card in the Chassis SlotCautionForcing the AT-SBx31CFC Card into its chass

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards118Figure 75. Closing the Locking Levers on the AT-SBx31CFC Central Fabric Controlle

SwitchBlade x3112 Installation Guide119Figure 76. Tightening the Thumb Screws on the AT-SBx31CFC Card9. Tighten the screws with a # 2 Phillips-head sc

List of Figures12

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards120Installing the Ethernet Line CardsThis section contains the installation procedur

SwitchBlade x3112 Installation Guide1213. Align the line card with the internal chassis card guides in the selected slot of the AT-SBx3112 Chassis.Fig

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards122Figure 79. Inserting an Ethernet Line Card5. Finger tighten the two thumbscrews o

SwitchBlade x3112 Installation Guide123Figure 80. Tightening the Thumb Screws on an Ethernet Line Card6. Tighten the two screws with a # 2 Phillips-he

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards124Installing the Blank Slot CoversAfter installing the AT-SBx31CFC Control Cards an

SwitchBlade x3112 Installation Guide125Figure 82. Tightening the Thumbscrews on a Blank Slot Cover3. Tighten the two screws with a # 2 Phillips-head s

Chapter 5: Installing the AT-SBx31CFC Card and Ethernet Line Cards126

127Chapter 6Installing the Transceivers and Cabling the PortsThis chapter describes how to install the fiber optic transceivers and attach the cables

Chapter 6: Installing the Transceivers and Cabling the Ports128Guidelines to Cabling the AT-SBx31GP24, AT-SBx31GT24, and AT-SBx31GT40 Line CardsHere a

SwitchBlade x3112 Installation Guide129For automatic MDIX detection to work successfully, the remote device connected to a port must also support the

13Table 1. Twisted Pair Cable for the AT-SBx31GT24 and AT-SBx31GT40 Line Cards ... 36Table 2. Twisted Pair Cable for

Chapter 6: Installing the Transceivers and Cabling the Ports130Figure 84. Connecting Cables to Ports on the AT-SBx31GT40 Line CardRelease TabConnectin

SwitchBlade x3112 Installation Guide131Guidelines to Installing SFP, SFP+, CSFP, and XFP TransceiversPlease review the following guidelines before ins

Chapter 6: Installing the Transceivers and Cabling the Ports132Installing SFP Transceivers in the AT-SBx31GS24 Line CardPlease review the information

SwitchBlade x3112 Installation Guide1333. To install the transceiver in an SFP slot on the top row of the line card, orient the transceiver with the h

Chapter 6: Installing the Transceivers and Cabling the Ports134NoteIf you are ready to attach the fiber optic cable to the transceiver, continue with

SwitchBlade x3112 Installation Guide1356. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 89. The connector should sn

Chapter 6: Installing the Transceivers and Cabling the Ports136Installing SFP and CSFP Transceivers in the AT-SBx31GC40 Line CardPlease review the inf

SwitchBlade x3112 Installation Guide1373. To install an SFP or a CSFP transceiver in a slot on the top row of the line card, orient it with the label

Chapter 6: Installing the Transceivers and Cabling the Ports138NoteIf you are ready to attach the fiber optic cable to the transceiver, continue with

SwitchBlade x3112 Installation Guide1396. Connect the fiber optic cables to the port on the transceiver, as shown in Figure 94. The connectors should

List of Tables14

Chapter 6: Installing the Transceivers and Cabling the Ports140Installing SFP+ Transceivers in the AT-SBx31XS6 Line CardPlease review the information

SwitchBlade x3112 Installation Guide141NoteDo not remove a dust plug from an SFP+ slot if you are not installing a transceiver. A dust plug protects t

Chapter 6: Installing the Transceivers and Cabling the Ports142NoteIf you are ready to attach the fiber optic cable to the transceiver, continue with

SwitchBlade x3112 Installation Guide1435. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 99. The connector should sn

Chapter 6: Installing the Transceivers and Cabling the Ports144Installing AT-SP10TW Cables in the AT-SBx31XS6 Line CardThis procedure explains how to

SwitchBlade x3112 Installation Guide145NoteDo not remove the dust plug from a SFP+ slot if you are not installing the transceiver at this time. The du

Chapter 6: Installing the Transceivers and Cabling the Ports1464. Install the other end of the cable into an SFP+ slot on another network device.5. Re

SwitchBlade x3112 Installation Guide147Installing XFP Transceivers in the AT-SBx31XZ4 Line CardPlease review the information in “Guidelines to Install

Chapter 6: Installing the Transceivers and Cabling the Ports1483. Orient the transceiver with the handle on top, as shown in Figure 104.Figure 104. Ha

SwitchBlade x3112 Installation Guide1495. Remove the protective cover from the fiber optic port on the XFP transceiver, as shown in Figure 106.Figure

15PrefaceThis guide contains the hardware installation instructions for the SwitchBlade x3112 switch. This preface contains the following sections: “

Chapter 6: Installing the Transceivers and Cabling the Ports1506. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 107

SwitchBlade x3112 Installation Guide151Cabling the NET MGMT Port on the AT-SBx31CFC CardThe control card must have access to your network if you want

Chapter 6: Installing the Transceivers and Cabling the Ports152 You must use a crossover cable to connect the port to a network device that operates

153Chapter 7Powering On the ChassisThis chapter describes how to power on the chassis, monitor the initialization process, and confirm the operational

Chapter 7: Powering On the Chassis154Verifying the InstallationPlease perform the following procedure before powering on the chassis:1. Verify that th

SwitchBlade x3112 Installation Guide155Powering On the AT-SBxPWRSYS1 AC Power SupplyThe procedure in this section explains how to power on the AT-SBxP

Chapter 7: Powering On the Chassis156If there are two system power supplies, you may power on either supply first. The illustration in Figure 109 show

SwitchBlade x3112 Installation Guide157Figure 110. Securing the Power Cord for the AT-SBxPWRSYS1 Power Supply to an Anchor4. Connect the power cord to

Chapter 7: Powering On the Chassis158Powering on the AT-SBxPWRPOE1 AC Power SupplyThis section contains instructions on how to power on the AT-SBxPWRP

SwitchBlade x3112 Installation Guide1593. Use the twist tie that comes with the power supply to secure the cord to an anchor on the chassis, as shown

Preface16Safety Symbols Used in this DocumentThis document uses the following conventions.NoteNotes provide additional information.CautionCautions inf

Chapter 7: Powering On the Chassis160Figure 113. Dress and Secure AC Power Cords6. Go to “Monitoring the Initialization Process” on page 184.

SwitchBlade x3112 Installation Guide161Powering On the AT-SBxPWRSYS1 DC System Power SupplyThis section contains instructions on how to power on the A

Chapter 7: Powering On the Chassis162Figure 114. Components of the AT-SBxPWRSYS1 DC Power SupplyWarningAs a safety precaution, install a circuit break

SwitchBlade x3112 Installation Guide163Choosing aMethod forAttaching theGrounding WireYou may attach the grounding wire to the power supply using the

Chapter 7: Powering On the Chassis1643. Use an 8 mm wrench to remove the grounding post nut and washer, shown in Figure 118, from the power supply.Fig

SwitchBlade x3112 Installation Guide165Figure 119. Installing the Grounding Wire5. Connect the other end of the grounding wire to the building protect

Chapter 7: Powering On the Chassis166Connecting theGrounding Wirewith Bare WireTo attach the grounding wire to the power supply with bare wire, perfor

SwitchBlade x3112 Installation Guide1674. Secure the wire with the nut and washer removed in step 2, and an 8 mm wrench, as shown in Figure 122.Figure

Chapter 7: Powering On the Chassis168NoteThe right angle terminals require the removal of the plastic cover from the terminal block.You may also insta

SwitchBlade x3112 Installation Guide169Figure 125. Attaching the Power Wires to the Power Terminal Lugs3. Use a #1 Phillips-head screwdriver to loosen

SwitchBlade x3112 Installation Guide17Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Telesis technical supp

Chapter 7: Powering On the Chassis170Figure 127. Removing the Terminal Screws5. With a #3 Phillips-head screwdriver, connect the power lead wires to t

SwitchBlade x3112 Installation Guide171Figure 128. Connecting the Power WiresWarningCheck to see if there are any exposed copper strands coming from t

Chapter 7: Powering On the Chassis172Figure 129. Closing the Plastic Cover over the Terminal ConnectorsCautionDo not over tighten the screws or you ma

SwitchBlade x3112 Installation Guide173Figure 130. Tightening the Handle Locking Screw8. Before attaching the power wires from the power supply to the

Chapter 7: Powering On the Chassis174Figure 131. Turning On the Power Supply12. Do one of the following: If the chassis has two AT-SBxPWRSYS1 DC Powe

SwitchBlade x3112 Installation Guide175Connecting theDC Power Wireswith the RightAngle TerminalsTo connect the DC power wires to the positive and nega

Chapter 7: Powering On the Chassis1763. Using a #1 Phillips-head screwdriver, remove the two screws that secure the plastic cover over the positive an

SwitchBlade x3112 Installation Guide177Figure 135. Removing the Terminal Screws5. Position the power wires over the terminals and secure them to the t

Chapter 7: Powering On the Chassis178Figure 136. Connecting the Power Wires

SwitchBlade x3112 Installation Guide179WarningCheck to see if there are any exposed copper strands coming from the installed wires. When this installa

Preface18

Chapter 7: Powering On the Chassis180Figure 138. Turning On the Power Supply11. Do one of the following: If the chassis has two AT-SBxPWRSYS1 DC Powe

SwitchBlade x3112 Installation Guide1812. Use a #1 Phillips-head screwdriver to loosen the two screws on the plastic cover over the positive and negat

Chapter 7: Powering On the Chassis182Figure 141. Connecting the Negative Lead WireAllied Telesis recommends tightening the screw to 30 to 40 inch-lbs.

SwitchBlade x3112 Installation Guide1837. With a #2 Phillips-head screwdriver, tighten the handle locking screw to secure the power supply to the chas

Chapter 7: Powering On the Chassis184Monitoring the Initialization ProcessThe control and line cards perform an initialization process when you power

SwitchBlade x3112 Installation Guide185with the active card does the inactive card begin to forward packets across the backplane.The phases of the ini

Chapter 7: Powering On the Chassis186synchronized its database with the active control card, at which point it turns solid amber to indicate the inact

SwitchBlade x3112 Installation Guide187Figure 143. Switch Initialization Messages (Continued)Loading vxWorks.bin.gz...(10152360 bytes)Starting at 0x10

Chapter 7: Powering On the Chassis188

189Chapter 8Verifying the Hardware Operations of the ChassisThis chapter describes how to verify the operations of the chassis. The chapter contains t

19Chapter 1OverviewThis chapter describes the SwitchBlade x3112 product in the following sections: “Introduction” on page 20 “AT-SBx3112 Chassis” on

Chapter 8: Verifying the Hardware Operations of the Chassis190Using the LEDs to Verify the ChassisAfter powering on the chassis for the first time and

SwitchBlade x3112 Installation Guide1915. To check the status of the Ethernet line cards, inspect the SBx Status LEDs on the control card. (If the cha

Chapter 8: Verifying the Hardware Operations of the Chassis192Using Local Management to Verify the ChassisThis section explains how to confirm the ope

SwitchBlade x3112 Installation Guide1932. Connect the other end of the cable to an RS-232 port on a terminal or personal computer with a terminal emul

Chapter 8: Verifying the Hardware Operations of the Chassis1942. Compare the version number displayed by the SHOW SYSTEM command with the information

SwitchBlade x3112 Installation Guide195Figure 147. SHOW FANMODULE Command5. To view the states of the control and line cards in the chassis, use the S

Chapter 8: Verifying the Hardware Operations of the Chassis196

197Chapter 9TroubleshootingThis chapter contains information on how to troubleshoot the SwitchBlade x3112 product.NoteIf you are unable to resolve a h

Chapter 9: Troubleshooting198AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power SuppliesA power supply is operating normally when its AC and DC LEDs are solid g

SwitchBlade x3112 Installation Guide199AT-SBxPWRSYS1 DC Power SupplyIf you suspect a problem with the DC power supply, examine its LEDs. The power sup

Copyright  2013 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview20IntroductionThe SwitchBlade x3112 product is a modular Gigabit and 10 Gigabit Ethernet switch. The main components are the AT-SBx

Chapter 9: Troubleshooting200software version on the control card, refer to “Using Local Management to Verify the Chassis” on page 192 and “Management

SwitchBlade x3112 Installation Guide201Ethernet Line CardsA quick and easy way to check the overall heath of the Ethernet line cards in the chassis is

Chapter 9: Troubleshooting202Command has been submittedofficer SEC>> Try installing the card in a different slot. If it works in the new slot,

SwitchBlade x3112 Installation Guide203Twisted Pair PortsThe ports on the AT-SBx31GT24 and AT-SBx31GP24 Line Cards have L/A LEDs that are solid or fla

Chapter 9: Troubleshooting204 The ports must be set to Auto-Negotiation, the default setting, to operate at 1000Mbps. The default duplex mode settin

SwitchBlade x3112 Installation Guide205Power Over EthernetThis section applies only to the AT-SBx31GP24 Line Card. Each port on the line card has two

Chapter 9: Troubleshooting206 Use the SHOW POE CARD command to determine whether the switch has reach its maximum power budget. Try connecting the P

SwitchBlade x3112 Installation Guide207Fiber Optic TransceiversThe L/A LEDs on the AT-SBx31GS24, AT-SBx31GC40, AT-SBx31XS6, and AT-SBx31XZ4 Line Cards

Chapter 9: Troubleshooting208and network device. The devices must be transmitting and receiving on opposite wavelengths. For example, if the fiber por

SwitchBlade x3112 Installation Guide209AT-SBx31CFC Central Fabric Controller CardThe consequences of a control card failure depend on the number of co

SwitchBlade x3112 Installation Guide21Figure 3. Ethernet Line Cards and AT-SBx31CFC Central Fabric Controller Card (Continued)The three power supplies

Chapter 9: Troubleshooting210AT-SBxFAN12 Fan ModuleThe AT-SBxFAN12 Fan Module is operating correctly when the POWER LED on the module is solid green.

SwitchBlade x3112 Installation Guide211Local (Out-of-Band) Management SessionIf you are unable to establish a local (out-of-band) management session w

Chapter 9: Troubleshooting212Power Supply Interfaces (Opto-couplers)The two power supply interfaces in the lower right corner of the rear panel are us

213Appendix ATechnical SpecificationsPhysical SpecificationsDimensions (W x D x H)Weight (Kilograms)Table 26. Product DimensionsAT-SBx3112 Chassis 4

Appendix A: Technical Specifications214AT-SBx31GP24 PoE Line Card 1.06 kg (2.34 lb)AT-SBx31GS24 SFP Line Card 1.06 kg (2.34 lb)AT-SBx31GC40 Line Card

SwitchBlade x3112 Installation Guide215Environmental SpecificationsNoteThe acoustic noise was measured at 40° C with the following products installed:

Appendix A: Technical Specifications216Power SpecificationsAC Voltage, Frequency Requirements (Volts, Hertz)DC Voltage RequirementTypical power saving

SwitchBlade x3112 Installation Guide217Maximum power supply efficiency (based on 100V input voltage)Heat dissipation (British Thermal Units/hour)Heat

Appendix A: Technical Specifications218Available Power over Ethernet (Watts/port):PoE ModeTable 36. Available Power Over Ethernet with One PoE Power

SwitchBlade x3112 Installation Guide219Safety and Electromagnetic Emissions CertificationsSafety and Electromagnetic Emissions:Table 39. Safety and

Chapter 1: Overview22The fan module is shown in Figure 5.Figure 5. Fan ModuleAT-SBxFAN12 Module, the cooling unit for the chassis

Appendix A: Technical Specifications220Port PinoutsThis section lists the port pinouts for the AT-SBx31GT24, AT-SBx31GT40, and AT-SBx31GP24 Line Cards

SwitchBlade x3112 Installation Guide221Table 42 lists the port pin signals when a 10/100/1000Base-T port is operating at 1000 Mbps.Table 42. 1000Bas

Appendix A: Technical Specifications222

SwitchBlade x3112 Installation Guide23AT-SBx3112 ChassisThe AT-SBx3112 Chassis is a 7RU unit. It has slots for ten Ethernet line cards, two control ca

Chapter 1: Overview24Figure 7. Rear View of the AT-SBx3112 ChassisFigure 8 is an example of a fully populated chassis.Figure 8. AT-SBx3112 Chassis wit

SwitchBlade x3112 Installation Guide25Ethernet Lineand ControlCards SlotsThe chassis has slots for ten Ethernet line cards and two AT-SBx31CFC Central

Chapter 1: Overview26The two right hand slots are for the AT-SBxPWRSYS1 Power Supply, which supplies power to the Ethernet line cards, control modules

SwitchBlade x3112 Installation Guide27AT-SBx31GT24 Line CardThe AT-SBx31GT24 Line Card, shown in Figure 11, is a Gigabit Ethernet switch.Figure 11. AT

Chapter 1: Overview28AT-SBx31GT40 Line CardThe AT-SBx31GT40 Line Card, shown in Figure 12, is a Gigabit Ethernet switch.Figure 12. AT-SBx31GT40 Line C

SwitchBlade x3112 Installation Guide29AT-SBx31GP24 PoE Line CardThe AT-SBx31GP24 PoE Line Card, shown in Figure 13, is a Gigabit Ethernet switch with

3Electrical Safety and Emissions StandardsThis product meets the following standards.EMI/RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN6

Chapter 1: Overview30AT-SBx31GS24 SFP Line CardThe AT-SBx31GS24 SFP Line Card, shown in Figure 14, is a Gigabit Ethernet switch.Figure 14. AT-SBx31GS2

SwitchBlade x3112 Installation Guide31AT-SBx31GC40 Line CardThe AT-SBx31GC40 Line Card, shown in Figure 15, is a Gigabit Ethernet switch.Figure 15. AT

Chapter 1: Overview32NoteThe AT-SBx31GC40 Line Card does not support 10 or 100 Mbps transceivers.The AT-SBx31GC40 Line Card has twenty slots for stand

SwitchBlade x3112 Installation Guide33AT-SBx31XZ4 XFP Line CardThe AT-SBx31XZ4 XFP Line Card, shown in Figure 16, is a 10 Gigabit Ethernet switch.Figu

Chapter 1: Overview34AT-SBx31XS6 SFP+ Line CardThe AT-SBx31XS6 Line Card, shown in Figure 17, is a 10 Gigabit Ethernet switch.Figure 17. AT-SBx31XS6 L

SwitchBlade x3112 Installation Guide3510/100/1000Base-T Twisted Pair PortsThis section applies to the 10/100/1000Base-T ports on the AT-SBx31GT24, AT-

Chapter 1: Overview36MaximumDistanceThe ports have a maximum operating distance of 100 meters (328 feet).CableRequirementsThe cable requirements for t

SwitchBlade x3112 Installation Guide37Automatic MDIXDetectionThe 10/100/1000 Mbps twisted-pair ports on the AT-SBx31GT24, AT-SBx31GT40, and AT-SBx31GP

Chapter 1: Overview38 You may use straight-through or crossover cables on ports that are connected to network devices that support automatic MDIX det

SwitchBlade x3112 Installation Guide39Power over Ethernet on the AT-SBx31GP24 Line CardThis section applies only to the AT-SBx31GP24 PoE Line Card. Th

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

Chapter 1: Overview40Power Budgeting The power for PoE is provided on the ports of the AT-SBx31GP24 Line Cards is provided by the AT-SBxPWRPOE1 Power

SwitchBlade x3112 Installation Guide41The PoE implementation on the AT-SBx31GP24 Line Card is Alternative A, in which power is transmitted over strand

Chapter 1: Overview42Port Numbers on the AT-SBx31GC40 Line CardThe AT-SBx31GC40 Line Card has two port numbers for each transceiver slot. The numbers

SwitchBlade x3112 Installation Guide43slot in the top row is port number 0 because it is the lower of the two port numbers of the slot. To configure t

Chapter 1: Overview44Port LEDs on the Ethernet Line CardsThe following sections define the port LEDs on the Ethernet line cards.AT-SBx31GT24Line CardE

SwitchBlade x3112 Installation Guide45AT-SBx31GT40Line CardThe LEDs for the ports on the AT-SBx31GT40 Line Card are found on the RJ point 5 cable conn

Chapter 1: Overview46AT-SBx31GP24Line CardEach port on the AT-SBx31GP24 PoE Line Card has two LEDs. The LEDs are shown in Figure 23 and described in T

SwitchBlade x3112 Installation Guide47Table 7. Port LEDs on the AT-SBx31GP24 PoE Line CardLED State DescriptionL/ASolid Green The port has establish

Chapter 1: Overview48AT-SBx31GS24Line CardThe SFP slots on the AT-SBx31GS24 SFP Line Card have one LED each, as shown in Figure 24 and described in Ta

SwitchBlade x3112 Installation Guide49AT-SBx31GC40Line CardThe AT-SBx31GC40 Line Card has two LEDs for each slot. The LEDS, which display link and act

5Preface ...

Chapter 1: Overview50When a slot has a standard SFP, only one LED of a pair is active. The other LED is not used. The active LED is different dependin

SwitchBlade x3112 Installation Guide51AT-SBx31XZ4Line CardEach XFP slot on the AT-SBx31XZ4 XFP Line Card has one LED. The LED is shown in Figure 28 an

Chapter 1: Overview52Table 11. SFP+ Slot LEDs on the AT-SBx31XS6 Line CardLED State DescriptionL/ASolid Green The transceiver has established a link

SwitchBlade x3112 Installation Guide53AT-SBx31CFC Central Fabric Controller CardThe AT-SBx31CFC Central Fabric Controller card has three primary funct

Chapter 1: Overview54The components on the card are identified in Figure 30.Figure 30. AT-SBx31CFC Central Fabric Controller CardSYS Status LEDs The S

SwitchBlade x3112 Installation Guide55SBx STATUSLEDsThe SBx STATUS LEDs display general status information about the Ethernet line cards and control c

Chapter 1: Overview56eco-friendlyButtonYou use the eco-friendly button on the control card to turn the LEDs on or off and test the LEDs. You may turn

SwitchBlade x3112 Installation Guide57CautionThe control and Ethernet line cards do not forward network traffic for a minimum of two minutes while the

Chapter 1: Overview58NET MGMTPortThe NET MGMT port is used by the control card to perform the features in Table 14. The control card uses the port to

SwitchBlade x3112 Installation Guide59The NET MGMT port has a standard RJ-45 8-pin connector and operates at 10, 100, or 1000 Mbps in either half- or

Contents6Console (RS-232) Port ...

Chapter 1: Overview60NET MGMTLEDThe Network Management (NET MGMT) port on the AT-SBx31CFC Central Fabric Controller card has one Status LED. The state

SwitchBlade x3112 Installation Guide61The following SD flash memory cards are officially supported in this release. SanDisk 2GB Flash card SanDisk 4

Chapter 1: Overview62Power SuppliesThere are three power supplies: AT-SBxPWRSYS1 AC Power Supply: This module supports all the hardware components in

SwitchBlade x3112 Installation Guide63NoteThe AT-SBxPWRSYS1 DC Power Supply is not compatible with the AT-SBxPWRSYS1 AC and AT-SBxPWRPOE1 AC Power Sup

Chapter 1: Overview64The LEDs on the AT-SBxPWRPOE1 AC Power Supply are described in Table 19.Table 18. LEDs on the AT-SBxPWRSYS1 DC Power SupplyLED

SwitchBlade x3112 Installation Guide65AT-SBxFAN12 ModuleThe AT-SBxFAN12 Module is the cooling unit for the chassis. It is a field- replaceable assembl

Chapter 1: Overview66Power Supply Interfaces (Opto-couplers)The chassis has two power supply interfaces, also referred to as opto-couplers, in the low

SwitchBlade x3112 Installation Guide67Module Names in the Management SoftwareThe line cards, control card, and fan module are referred to in the manag

Chapter 1: Overview68Management Software Releases for the Hardware ComponentsTable 23 lists the management software releases for the hardware componen

69Chapter 2Safety Precautions and Site PreparationThis chapter contains the safety precautions and guidelines for selecting a site for the chassis. Th

SwitchBlade x3112 Installation Guide7Connecting the DC Power Wires with the Right Angle Terminals...

Chapter 2: Safety Precautions and Site Preparation70Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to ins

SwitchBlade x3112 Installation Guide71NotePluggable Equipment. The socket outlet shall be installed near the equipment and shall be easily accessible.

Chapter 2: Safety Precautions and Site Preparation72WarningMounting of the equipment in the rack should be such that a hazardous condition is not crea

SwitchBlade x3112 Installation Guide73WarningTo reduce the risk of electric shock, the PoE ports on this product must not connect to cabling that is r

Chapter 2: Safety Precautions and Site Preparation74Selecting a Site for the SwitchBlade x3112Please observe the following site requirements for the s

SwitchBlade x3112 Installation Guide75Figure 33. 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle

Chapter 2: Safety Precautions and Site Preparation76

77Chapter 3Installing the Chassis in an Equipment RackThis chapter describes how to install the AT-SBx3112 Chassis in an equipment rack. This chapter

Chapter 3: Installing the Chassis in an Equipment Rack78Required Tools and MaterialHere is a list of the tools and material you need to install the pr

SwitchBlade x3112 Installation Guide79Preparing the Equipment RackThis section explains how to prepare the equipment rack for the installation of the

Contents8

Chapter 3: Installing the Chassis in an Equipment Rack80Figure 34. Reserving Vertical Rack Space3. Identify the lowest 1/2” screw hole pattern on the

SwitchBlade x3112 Installation Guide81Figure 35. Rack Mounting Hole Locations5. After installing the two screws in the equipment rack, go to “Unpackin

Chapter 3: Installing the Chassis in an Equipment Rack82Unpacking the AT-SBx3112 ChassisTo unpack the AT-SBx3112 Chassis, perform the following proced

SwitchBlade x3112 Installation Guide83Figure 37. AT-SBx3112 Chassis Items (Continued)Two equipment rack brackets pre-installed on the sides of the cha

Chapter 3: Installing the Chassis in an Equipment Rack84Adjusting the Equipment Rack BracketsYou may change the positions of the two pre-installed equ

SwitchBlade x3112 Installation Guide85Figure 38. Rack Mounting Bracket LocationsFigure 39. Rack Bracket Locations for Reverse Position of ChassisFacto

Chapter 3: Installing the Chassis in an Equipment Rack86Installing the AT-SBx3112 Chassis in the Equipment RackThe procedure in this section explains

SwitchBlade x3112 Installation Guide872. Lift the AT-SBx3112 Chassis into the equipment rack and set the bottom of the equipment rack brackets firmly

Chapter 3: Installing the Chassis in an Equipment Rack88Figure 41. Installing the Rack Mount Screws5. Tighten all eight screws to secure the chassis t

SwitchBlade x3112 Installation Guide89Removing the Shipping BraceNow that the chassis is installed in the equipment rack, you may remove the shipping

9FiguresFigure 1: AT-SBx3112 Chassis ...

Chapter 3: Installing the Chassis in an Equipment Rack90Installing the Chassis Grounding LugThis procedure explains how to connect a ground wire to th

SwitchBlade x3112 Installation Guide913. Insert one end of the grounding wire into the grounding lug, as shown in Figure 45, and use a crimping tool t

Chapter 3: Installing the Chassis in an Equipment Rack92

93Chapter 4Installing the Power SuppliesThis chapter explains how to install the power supplies. It has the following sections: “Protecting Against E

Chapter 4: Installing the Power Supplies94Protecting Against Electrostatic Discharge (ESD)To protect the equipment from damage by Electrostatic Discha

SwitchBlade x3112 Installation Guide95Installing the AT-SBxPWRSYS1 AC System Power SupplyFor background information on the AT-SBxPWRSYS1 AC Power Supp

Chapter 4: Installing the Power Supplies96Figure 49. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the new AT-SBxPWRSYS1 AC Power Su

SwitchBlade x3112 Installation Guide97Figure 50. Items Included with the AT-SBxPWRSYS1 Power Supply ModuleNoteStore the packaging material in a safe l

Chapter 4: Installing the Power Supplies98Figure 51. Verifying the AT-SBxPWRSYS1 AC Power Supply5. Move the locking handle on the AT-SBxPWRSYS1 AC Pow

SwitchBlade x3112 Installation Guide99Figure 53. Inserting the AT-SBxPWRSYS1 AC Power Supply7. Lower the power supply locking handle to secure the pow