Allied-telesis AT-FS708 Uživatelský manuál

613-001268 Rev. AFast Ethernet SwitchAT-FS708Installation Guide

10Chapter 1Product DescriptionThis chapter contains the follows sections: “Overview” on page 11 “Key Features” on page 12 “Hardware Feature Descrip

AT-FS708 Fast Ethernet Switch Installation Guide11OverviewThe AT-FS708 switch is an unmanaged eight-port Fast Ethernet switch. This switch offers a ra

Chapter 1: Product Description12Key Features The AT-FS708 switch has the following key features: Eight 10/100 Mbps (10Base-T / 100Base-TX) twisted pa

AT-FS708 Fast Ethernet Switch Installation Guide13Hardware Feature DescriptionThe sections below describe the hardware features of the AT-FS708 Fast E

Chapter 1: Product Description14For 10 Mbps operation, Category 3 or better 100 ohm shielded or unshielded twisted pair cabling is required. For 100 M

AT-FS708 Fast Ethernet Switch Installation Guide15ECOFriendlyPush ButtonThe ecoFriendly switch on the front panel may be used to turn ON or OFF the po

Chapter 1: Product Description16A Few Ethernet Switching BasicsAn Ethernet switch interconnects network devices, such as workstations, printers, route

AT-FS708 Fast Ethernet Switch Installation Guide17Duplex Mode Duplex mode refers to how an end node receives and transmits data. If an end node can re

Chapter 1: Product Description18A port operating in full-duplex mode uses PAUSE frames, as specified in the IEEE 802.3x standard, to stop the transmis

19Chapter 2InstallationThis chapter contains the following sections: “Reviewing Safety Precautions” on page 20 “Selecting a Site for the Switch” on

Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 2: Installation20Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the switch. NoteImport

AT-FS708 Fast Ethernet Switch Installation Guide21All Countries: Install product in accordance with local and National Electrical Codes.  E8Warning:

Chapter 2: Installation22Selecting a Site for the SwitchObserve the following requirements when choosing a site for the AT-FS708 Fast Ethernet switch:

AT-FS708 Fast Ethernet Switch Installation Guide23Planning the InstallationTable 3 contains the cabling specifications for the twisted pair ports.Note

Chapter 2: Installation24Unpacking the SwitchTo unpack an AT-FS708 switch, perform the following procedure:1. Remove all components from the shipping

AT-FS708 Fast Ethernet Switch Installation Guide25Installing the Switch on a Table or DesktopTo install the switch on a table or desktop, perform the

Chapter 2: Installation26Wall-Mounting the SwitchThe switch can be mounted vertically on a wall using the mounting brackets that come with the unit. T

AT-FS708 Fast Ethernet Switch Installation Guide277. Align the switch horizontally. And then position and hang the switch onto the wall using the two

Chapter 2: Installation28Installing the Switch in a RackPerform the following procedure to install the switch in a standard 19-inch rack. 1. If attach

AT-FS708 Fast Ethernet Switch Installation Guide293. Mount the switch in a 19-inch rack using rack mounting screws (not provided), as shown in Figure

3Electrical Safety and Emissions StandardsThis product meets the following standards.EMI FCC Class B, CISPR 22 Class B, EN55022 Class B, C-TICK, CEImm

Chapter 2: Installation30Cabling the SwitchTo connect the twisted pair cables to the ports on the AT-FS708 switch, perform the following procedure:1.

AT-FS708 Fast Ethernet Switch Installation Guide31Powering On the SwitchTo apply power to the AT-FS708 switch without the optional power cord retainin

32Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the switch in the event a problem occurs.NoteIf you are still unabl

33Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: (W x D x H)250 mm x 117 mm x 36.5 mm(9.84 in x 4.60 in x 1.44 in)Weight: 0.75 k

Appendix A: Technical Specifications34Safety and Electromagnetic Emissions CertificationsEMI FCC Part 15 Class B, CISPR 22 Class B, EN55022 Class B, I

AT-FS708 Fast Ethernet Switch Installation Guide35RJ-45 Twisted Pair Port ConnectorsThis section lists the connectors and connector pinouts for the AT

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

5Preface ...

6PrefaceThis guide contains instructions on how to install the AT-FS708 Fast Ethernet switch. This preface contains the following sections: “Safety S

AT-FS708 Fast Ethernet Switch Installation Guide7Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1.

Preface8Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are available in portable document format (PDF)

AT-FS708 Fast Ethernet Switch Installation Guide9Contacting Allied Telesis This section provides Allied Telesis contact information for technical supp