Allied-telesis AT-S80 Uživatelský manuál Strana 111
- Strana / 346
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AT-S80 Management Software User’s Guide
Section I: Using the Menus Interface 111
Displaying the VLANs
To display a list of the port-based and tagged VLANs on the switch,
perform the following procedure:
1. From the Main Menu, type A to select Advanced Switch
Configuration.
The Advanced Switch Configuration Menu is shown in Figure 14 on
page 64.
2. From the Advanced Switch Configuration Menu, type V to select VLAN
Management.
The VLAN Management Menu is shown in Figure 21 on page 103.
3. Type V to select 802.1Q VLAN.
The Tagged-based VLAN configuration Menu is shown in Figure 22 on
page 104. The currently configured VLANs are displayed in a table
with the following columns of information:
VLAN ID
The ID of the VLAN.
VLAN Name
The name of the VLAN.
VLAN Type
The type of VLAN, either permanent or static. Only the Default VLAN is
permanent. All other port-based and tagged VLANs are static.
4. To view the ports of a VLAN, type O to select Config VLAN Member.
The following prompt is displayed:
Enter VLAN ID>
5. Enter the VID of the VLAN you want to view and press Enter.
The range of the VID is from 2 to 4094.
- User’s Guide 1
- Contents 3
- Document Conventions 15
- Contacting Allied Telesis 16
- Overview 17
- Management Overview 18
- Remote SNMP Management 20
- Management Access Level 21
- AT-FS750/24 Switch 22
- Using the Menus Interface 23
- Interface 25
- Enter system location> 37
- Enter system contact> 37
- Enter entry number> 40
- Enter new user name> 40
- Enter new password> 40
- Retype new password 42
- Retype new password> 42
- Viewing Switch Information 43
- Rebooting the Switch 46
- Enter new timeout value> 49
- Figure 12. Ping Results 50
- Chapter 4: Port Configuration 54
- Enabling and Disabling a Port 56
- Enter new mode for port 57
- (a/h/H/f/F/T)> 57
- Port Trunking Overview 62
- Trunk” on page 69 63
- (E/D)> 66
- Chapter 5: Port Trunking 68
- Enter trunk group number> 69
- IGMP Snooping Overview 72
- Setting the Age 76
- Setting Group 76
- Chapter 6: IGMP Snooping 78
- Static Multicast Address 79
- Adding a Static 81
- Multicast 81
- Deleting a Static 82
- Member Port 83
- Port Mirroring Overview 86
- Chapter 8: Port Mirroring 88
- Dial-in User Configuration 91
- Configuring a Dial-in User 93
- Deleting a Dial-in 94
- Modifying a 95
- VLAN Overview 98
- Port-based VLANs 99
- Tagged VLANs 99
- Port-based VLAN Overview 100
- Tagged VLAN Overview 101
- Port VLAN 102
- Identifier 102
- General Rules for 102
- Creating a 102
- Tagged VLAN 102
- Creating a VLAN 103
- Chapter 10: Virtual LANs 104
- Changing the 109
- Changing Port 110
- VLAN Type 110
- Displaying the VLANs 111
- Modifying a VLAN 114
- Enter new VLAN name> 115
- Deleting a VLAN 116
- Deleting a Tagged 117
- Chapter 11 119
- SNMP Overview 120
- Community String Attributes 121
- Creating an SNMP Community 124
- Deleting an 126
- Community 126
- Modifying an 127
- Enter community name> 128
- Creating an SNMP Host 129
- Deleting an Host 130
- Host Entry 131
- Enter IP address for host> 132
- Enabling an 133
- SNMP Trap 133
- Deleting a Trap 135
- Receiver 135
- Modifying a Trap 135
- Enabling or 137
- Disabling Traps 137
- Quality of Service (QoS) 139
- QoS Overview 140
- [T]raffic Class Configuration 143
- [P]ort Priority Configuration 143
- [Q]uit to previous menu 143
- Command> 143
- Chapter 13 149
- RSTP Overview 150
- Path Costs and Port Costs 151
- Port Priority 152
- Point-to-Point and Edge Ports 153
- Point-to-Point Ports 154
- (Full-duplex Mode) 154
- 87654321 155
- Rapid Spanning 156
- Tree and VLANs 156
- Enabling or Disabling RSTP 157
- Enter bridge priority> 160
- Enter bridge hello time> 160
- Enter bridge maximum age> 161
- Configuring STP Compatibility 162
- Configuring the 163
- Basic RSTP Port 163
- Settings 163
- Advanced RSTP 165
- Port Settings 165
- Displaying the RSTP Topology 168
- Bandwidth Control 171
- Bandwidth Control Overview 172
- Configuring Bandwidth Control 173
- Setting the 174
- Ingress Limit 174
- Setting Ingress 174
- DLF Status 175
- Chapter 14: Bandwidth Control 176
- IP Access List 177
- IP Access List Overview 178
- Configuring IP Access List 179
- Adding or 180
- Removing IP 180
- Addresses 180
- Destination MAC Filter 181
- Destination MAC 183
- Filtering 183
- Removing 184
- Chapter 17 185
- Authentication 187
- Authenticator 187
- Port-based 189
- Network Access 189
- Guidelines 189
- Switch A 191
- Switch B 191
- Guest VLANs 192
- Enter port number> 194
- Enter guest VLAN ID > 195
- Chapter 18 201
- RADIUS Overview 202
- Configuring the RADIUS Client 203
- Management Software Updates 207
- Enter file name > 210
- Enter retry count > 210
- Download file? (Y/N) > 210
- Section II 211
- Chapter 20 213
- Switch’s IP Address 214
- Web Browser Tools 217
- Basic Switch Parameters 219
- Setting Up the IP Access List 222
- Then click Add 223
- Deleting an IP 224
- Adding System 228
- Administration 228
- Information 228
- Modifying 229
- Deleting 230
- Viewing System Information 233
- Rebooting a Switch 236
- Pinging a Remote System 238
- 3. Click Start 239
- Port Configuration 241
- 10/100BaseTX - Base ports 243
- Port Trunking 245
- Creating a Port Trunk 246
- Modifying a Port Trunk 248
- Chapter 23: Port Trunking 250
- Port Mirroring 251
- Configuring Port Mirroring 252
- Disabling Port Mirroring 253
- Chapter 24: Port Mirroring 254
- Chapter 25 255
- Deleting a Group MAC Address 259
- IGMP Snooping 261
- Configuring IGMP Snooping 262
- Chapter 26: IGMP Snooping 264
- Chapter 27 265
- Removing a MAC Address 268
- Chapter 28: Bandwidth Control 272
- Virtual LANs 273
- Assigning Ports to a VLAN 274
- Creating a Tagged VLAN 275
- Chapter 29: Virtual LANs 276
- Modifying a Tagged VLAN 277
- Deleting a Tagged VLAN 279
- Creating a Port-Based VLAN 280
- Modifying a Port-Based VLAN 281
- Deleting a Port-Based VLAN 283
- Chapter 30 285
- Modifying an SNMP Community 287
- Deleting an SNMP Community 288
- Creating a Host Table 289
- Modifying a Host Table Entry 290
- Deleting a Host Table Entry 291
- Enabling or Disabling Traps 292
- Modifying Traps 293
- Deleting Traps 294
- Configuring CoS 298
- Chapter 32 301
- Basic RSTP Configuration 302
- Viewing the RSTP Topology 309
- Control Feature 311
- Dial-in User 317
- Adding a Dial-in User 318
- Modifying a Dial-in User 319
- Deleting a Dial-in User 320
- Chapter 35 321
- Statistics 329
- Displaying Switch Statistics 330
- Chapter 37: Statistics 332
- – Light Yellow 334
- – Light Gray 334
- Displaying Error 335
- Group Statistics 335
- Displaying 337
- Historical Status 337
- Appendix A 339
Související produkty a manuály pro Počítačový hardware Allied-telesis AT-S80
Počítačový hardware Allied-telesis AlliedView-EMS 3.10 DEVICE MANAGER Uživatelský manuál
(133 stránky)
(133 stránky)
Počítačový hardware Allied-telesis AT-CM20x Series Converteon Line Cards Uživatelský manuál
(2 stránky)
(2 stránky)
Počítačový hardware Allied-telesis AT-CM212x/1 Series Converteon Line Cards Uživatelský manuál
(2 stránky)
(2 stránky)
Počítačový hardware Allied-telesis AT-CV10x Series Converteon Line Cards Uživatelský manuál
(2 stránky)
(2 stránky)
Počítačový hardware Allied-telesis Telesyn AlliedView NMS System 9.0 Uživatelský manuál
(64 stránky)
(64 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.367 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce