Allied-telesis AT-CV1203 Uživatelský manuál

613-000331 Rev. CCONVERTEON™ FamilyTwo-Slot ChassisAT-CV1200AT-CV1203Installation Guide

Tables10

11PrefaceThis guide contains instructions on how to install the AT-CV1200 or AT-CV1203 two-slot Converteon chassis. This preface contains the followin

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-CV120x Two-Slot Chassis Installation Guide13Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are avai

Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate inform

15Chapter 1OverviewThis chapter contains the following sections: “Features” on page 16 “AT-CV5M0x Management Card” on page 18 “AT-CVMNT12 Wall-Moun

Chapter 1: Overview16FeaturesThe AT-CV1200 and AT-CV1203 chassis look physically the same, as shown in Figure 1. These chassis are dual-slot chassis f

AT-CV120x Two-Slot Chassis Installation Guide17available from your Allied Telesis sales representative.Front and BackPanelsFigure 2 shows the front an

Chapter 1: Overview18AT-CV5M0x Management CardThe AT-CV5M0x Management Card provides a CPU subsystem for the Allied Telesis Converteon Series chassis

AT-CV120x Two-Slot Chassis Installation Guide19AT-CVMNT12 Wall-Mount BracketThe AT-CVMNT12 Wall-Mount Bracket, shown in Figure 4, is a bracket designe

Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Overview20Blank Slot CoverThe AT-CV5PNL1 blank slot cover is designed to maintain optimal, trouble-free environmental conditions for the AT

AT-CV120x Two-Slot Chassis Installation Guide21Power AdapterThe AT-CV120x chassis uses a two-part AC power adapter (supplied) as shown in Figure 6.Fig

Chapter 1: Overview22LEDsFigure 7 shows the location of the rear panel power LEDs which are described in Table 1.Figure 7. Power LEDs on the Rear Pane

AT-CV120x Two-Slot Chassis Installation Guide23Network TopologiesThis section describes the network topologies you can create with the AT-CV1200 Two-S

Chapter 1: Overview24Back-to-BackTopologyFigure 9 shows a back-to-back topology using two AT-CV1200 chassis with two AT-CM202 line cards, with one lin

AT-CV120x Two-Slot Chassis Installation Guide25

Chapter 1: Overview26

27Chapter 2InstallationThis chapter contains the following installation procedures for the AT-CV120x chassis: “Reviewing Safety Precautions” on page

Chapter 2: Installation28Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any of

AT-CV120x Two-Slot Chassis Installation Guide29Selecting a Site for the ChassisObserve the following requirements when choosing a site for the chassis

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-

Chapter 2: Installation30Unpacking the ChassisTo unpack the chassis, perform the following procedure:1. Remove all components from the shipping packag

AT-CV120x Two-Slot Chassis Installation Guide31Using the AT-CV120x Chassis on a DesktopTo use the AT-CV120x chassis on a desktop, perform the followin

Chapter 2: Installation32Powering On an AT-CV120x ChassisThe AT-CV120x chassis is shipped with one AC power adapter which powers both slot 1 and slot

AT-CV120x Two-Slot Chassis Installation Guide33Installing a Converteon Line CardTo install any Converteon line card including the AT-CV5M0x Management

Chapter 2: Installation345. Set the line card’s DIP switches if necessary.For more information on the DIP switch settings, refer to the documentation

AT-CV120x Two-Slot Chassis Installation Guide35Installing an AT-CM70S Line CardThe AT-CM70S line card is a double-slot line card which takes both line

Chapter 2: Installation365. Align the back edge of the line card with the bottom left and right alignment guides located inside the slot.6. Slide the

AT-CV120x Two-Slot Chassis Installation Guide37Installing a Blank Slot CoverThe AT-CV5PNL1 blank slot covers are used to cover the unoccupied line car

Chapter 2: Installation388. Use a Phillips screwdriver to tighten the captive screw, as shown in Figure 19.Figure 19. Tightening the Captive Screw on

AT-CV120x Two-Slot Chassis Installation Guide39Warranty RegistrationAllied Telesis hardware products are covered under limited warranties. Some produc

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled Translated Sa

Chapter 2: Installation40

41Chapter 3TroubleshootingThis chapter contains information about how to troubleshoot the chassis and line cards in the event that a problem occurs.No

Chapter 3: Troubleshooting42If one of the power supplies is connected but its LED remains OFF, perform the following: Verify that the power cord of t

43Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: (H x W x L):5.40 cm x 13.12 cm x 15.52 cm(2.12 in x 5.17 in x 6.11 in)Weight: 0

Appendix A: Technical Specifications44Safety and Electromagnetic Emissions CertificationsEMI: FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CEIm

5Preface ...

Contents6

7Figure 1. AT-CV120x Chassis ...

Figures8

9Table 1. Safety Symbols ..............................