Allied Telesis AT-8100S/24C Uživatelská příručka Strana 59
- Strana / 350
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AlliedWare Plus Version 2.2.4 Management Software Web Browser User’s Guide
59
Rebooting a Switch
Resetting the switch ends your web browser management session. To
continue managing the switch, you must login again.
Note
All unsaved changes are discarded when you reset a switch. To
save your changes to the startup configuration file, click SAVE.
To reboot a switch, perform the following procedure:
1. Select the System Tab.
The System Settings Tab is displayed. See Figure 9 on page 41.
2. From the System Settings tab, select Dashboard.
The Dashboard Page is displayed. See Figure 3 on page 28.
3. Select Reboot
at the bottom of the page.
A confirmation prompt is displayed that indicates that the connection to
the web is lost during a reboot.
4. Click OK to reset the switch or Cancel to cancel the procedure.
Note
The switch does not forward packets while it initializes the
AlliedWare Plus™ software and loads its active configuration file.
This process takes between 20 seconds to 2 minutes to complete,
depending on the number and types of commands in the
configuration file.
- AT-8100 Series 1
- Copyright 2
- Contents 10
- Document Conventions 16
- Contacting Allied Telesis 18
- Chapter 1 19
- Management Sessions 20
- Web Manager Accounts 21
- Starting a Management Session 23
- Figure 1. Login Page 26
- Logging on to the Switch 27
- What to Configure First 30
- Setting System 31
- When You Do 32
- Not Know the IP 32
- Address of the 32
- Baud rate: 9600 33
- Data bits: 8 33
- Parity: None 33
- Stop bits: 1 33
- Flow control: None 33
- Enabling HTTP 35
- Service in the 35
- Saving your 36
- Changes in the 36
- Saving Your Changes 37
- 8 on page 37 38
- Chapter 3 39
- Configuring an 40
- SNTP or NTP 40
- Time Manually 42
- Deleting a 52
- Managing Local User Accounts 53
- Changing a User 55
- Password 55
- Changing the 56
- User Privilege 56
- Deleting a User 57
- 5. Click Delete User 58
- Rebooting a Switch 59
- Upgrading the Software 60
- Default Values 63
- Displaying System Information 64
- Chapter 4 67
- Port Numbers on the Switch 68
- Changing the Port Settings 72
- Chapter 5 81
- Displaying Port Statistics 82
- Receive Statistics 83
- Transmit 85
- Statistics 85
- Interface 87
- Clearing Port Statistics 89
- Reloading Statistics 90
- Chapter 6 91
- Chapter 6: Port Mirroring 94
- Assigning a Destination Port 95
- Chapter 7 99
- Overview 100
- Chapter 8 107
- Chapter 9 117
- Displaying LACP Trunks 119
- Adding an LACP Trunk 121
- Modifying an LACP Trunk 123
- Deleting an LACP Trunk 125
- Chapter 10 127
- Adding Static Trunks 131
- Deleting Static Trunks 137
- Chapter 11 139
- Tagged and 141
- Untagged Ports 141
- Displaying VLANs 142
- Adding an VLAN 143
- Modifying VLANs 145
- Assigning a Native VLAN 148
- Deleting VLANs 152
- Chapter 12 153
- Chapter 13 159
- Disabling IGMP Snooping 164
- Displaying the Routers List 165
- IGMP query from it 166
- Clearing the Routers List 167
- Displaying the Hosts List 168
- Chapter 14 171
- Assigning 173
- Multiple Queriers 173
- .2 Enabled Enabled Active 175
- .3 Enabled Disabled None 175
- .4 Enabled Enabled Standby 175
- Guidelines 176
- VLAN— Indicates the VLAN ID 178
- 5. Click Apply 180
- 6. Click SAVE 180
- Chapter 15 181
- Prioritization 183
- Displaying PoE Port Settings 184
- Chapter 16 191
- Chapter 17 199
- Server 1 202
- Configuring 203
- Remote Manager 203
- Authentication 203
- Using RADIUS 203
- Adding a 206
- RADIUS Server 206
- Using TACACS+ 208
- Chapter 18 215
- Authenticator Role: 217
- Single host mode 217
- Multiple host mode 218
- Multiple supplicant mode 218
- Dynamic VLAN 219
- Assignments 219
- Authenticator 223
- Chapter 19 229
- IP Management 231
- Displaying IPv4 Interfaces 232
- Adding an IPv4 Address 234
- 5. Click Add 235
- Changing an IPv4 Address 236
- Deleting an IPv4 Address 238
- Displaying the IPv6 Interface 239
- Adding an IPv6 Address 241
- Changing IPv6 Addresses 243
- Deleting IPv6 Addresses 245
- Chapter 20 247
- Creating an ACL 251
- Assigning an ACL to Ports 255
- Displaying a List of ACLs 257
- Chapter 21 259
- Displaying Static Routes 260
- Adding a Static Route 262
- Deleting a Static Route 264
- Displaying the Routing Table 265
- Chapter 22 267
- Creating a QoS Policy 271
- Chapter 23 279
- Changing the RIP Settings 286
- Displaying RIP Statistics 288
- Reloading RIP Statistics 290
- Chapter 24 291
- Displaying the ARP Table 293
- Adding a Static ARP Entry 295
- Deleting ARP Entries 297
- Chapter 25 299
- Optional LLDP-MED TLVs 301
- Chapter 25: LLDP and LLDP-MED 302
- Disabling LLDP on the Switch 305
- Configuring LLDP on a Port 306
- Selecting LLDP TLVs on a Port 308
- Figure 128. LLDP TLV Page 309
- 5. Click Edit 309
- Creating a Civic 312
- Location Entry 312
- Figure 130. Locations Tab 313
- Creating a 316
- Coordinate 316
- Location 316
- Displaying LLDP Statistics 329
- Tab selected 331
- Displaying Location Entries 332
- Displaying 333
- Locations 333
- Displaying ELIN 334
- Displaying the 335
- Basic LLDP 335
- Configuration 335
- Displaying LLDP 336
- Port Assignments 336
- Displaying Port 337
- LLDP-MED TLV 339
- - Model Name 340
- - Asset ID 340
- Chapter 26 341
- Configuring sFlow on a Port 344
- Chapter 26: sFlow 346
- Enabling sFlow on the Switch 348
- Displaying the sFlow Settings 349
- End of Document 350
Související produkty a manuály pro Software Allied Telesis AT-8100S/24C
Software Allied Telesis AT-FS750/48 Uživatelská příručka
(234 stránky)
(234 stránky)
Software Allied Telesis AT-GS950/16 Uživatelská příručka
(348 stránky)
(348 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce