Allied Telesis Switch AT-9000 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Operační systémy Allied Telesis Switch AT-9000. Allied Telesis Switch AT-9000 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 12
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
PN 613-001447 Rev A 1
4
AlliedWare Plus™ Version 2.1.2
AT-9000 Layer 2-4 Gigabit Ethernet EcoSwitches
Software Release Notes
Please read this document before you begin to use the management software. The document
has the following sections:
“Supported Platforms” on page 1
“What’s New in Version 2.1.2” on page 2
“Introduction to Upgrading the Switch” on page 2
“Upgrading the AT-9000 Switch to AlliedWare Plus Version 2.1.2 from Version 2.1.1” on
page 3
“Troubleshooting the Upgrade Procedure” on page 6
“Operational Notes” on page 6
“Resolved Issues” on page 7
“Known Issues” on page 8
“Changes to the AlliedWare Plus Command Line User’s Guide” on page 9
“Contacting Allied Telesis” on page 12
Caution:
The software described in this document contains certain cryptographic functionality and its
export is restricted by U.S. law. As of this writing, it has been submitted for review as a “retail
encryption item” in accordance with the Export Administration Regulations, 15 C.F.R. Part 730-
772, promulgated by the U.S. Department of Commerce, and conditionally may be exported in
accordance with the pertinent terms of License Exception ENC (described in 15 C.F.R. Part
740.17). In no case may it be exported to Cuba, Iran, Iraq, Libya, North Korea, Sudan, or Syria. If
you wish to transfer this software outside the United States or Canada, please contact your local
Allied Telesis sales representative for current information on this product’s export status.
Supported Platforms
Version 2.1.2 of the AlliedWare Plus™ Management Software is supported on these switches:
AT-9000/28
AT-9000/28SP
AT-9000/52
This version supports the following SFP modules:
AT-SPTX (Supported only at a speed of 1G.)
Zobrazit stránku 0
1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - Software Release Notes

PN 613-001447 Rev A 14AlliedWare Plus™ Version 2.1.2AT-9000 Layer 2-4 Gigabit Ethernet EcoSwitchesSoftware Release NotesPlease read this document befo

Strany 2

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 10 Allied Telesis, Inc.Chapter 52: MAC Address-based Port SecurityRevision A o

Strany 3

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 11 Allied Telesis, Inc.Chapter 77: SSH Server CommandsThe following commands d

Strany 4

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 12 Allied Telesis, Inc.Contacting Allied TelesisThis section provides Allied T

Strany 5

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 2 Allied Telesis, Inc.AT-SPEX AT-SPSX AT-SPFX/2 AT-SPFX/15 AT-SPLX10 AT-

Strany 6

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 3 Allied Telesis, Inc.Upgrading the AT-9000 Switch to AlliedWare Plus Version

Strany 7

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 4 Allied Telesis, Inc.This example of the command uploads the boot configurati

Strany 8

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 5 Allied Telesis, Inc.After you enter a banner command, the prompt “Type CTRL/

Strany 9

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 6 Allied Telesis, Inc.SET SFLOW COLLECTOR IP Command - In v2.1.1 this command

Strany 10

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 7 Allied Telesis, Inc.— VLAN stackingUse the command line interface to configu

Strany 11

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 8 Allied Telesis, Inc.Port-based and tagged VLANs: You could not change a por

Strany 12

AlliedWare Plus Version 2.1.2 Software Release NotesPN 613-001447 Rev A 9 Allied Telesis, Inc.Changes to the AlliedWare Plus Command Line User’s Guide

Komentáře k této Příručce

Žádné komentáře