Allied-telesis AT-S63 Uživatelský manuál Strana 275
- Strana / 468
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AT-S63 Stack Command Line User’s Guide
Section III: Snooping Protocol 275
SHOW IGMPSNOOPING
Syntax
show igmpsnooping
Parameters
None.
Description
This command displays the IGMP parameters. Figure 31 illustrates the
information that is displayed by this command.
Figure 31. SHOW IGMPSNOOPING Command
For an explanation of these parameters, refer to “SET IP IGMP” on
page 272 and “SHOW IP IGMP” on page 277.
IGMP Snooping Configuration:
IGMP Snooping Status ............... Disabled
Host Topology ...................... Single-Host/Port (Edge)
Host/Router Timeout Interval ....... 260 seconds
Maximum IGMP Multicast Groups ...... 64
Router Port(s) ..................... Auto Detect
Router List:
VLAN Port/ IGMP Exp.
ID Trunk ID RouterIP Ver. time
---------------------------------------------------------
1 14/- 172.16.01.1
Host List:
Number of IGMP Multicast Groups: 4
VLAN Port/ IGMP Exp.
MulticastGroup ID TrunkID HostIP Ver Time
------------------------------------------------------------
01:00:5E:00:01:01 1 6/- 172.16.10.51 v2 21
01:00:5E:7F:FF:FA 1 5/- 149.35.200.75 v2 11
149.35.200.65 v2 65
01:00:5E:00:00:02 1 17/- 149.35.200.69 v2 34
01:00:5E:00:00:09 1 14/- 172.16.10.51 v2 32
- Command Line 1
- User’s Guide 1
- Contents 10
- How This Guide is Organized 14
- Product Documentation 16
- Where to Go First 17
- Starting a Management Session 18
- Document Conventions 19
- Contacting Allied Telesis 21
- Basic Operations 23
- Introduction 26
- AT-S63 Management Software 27
- Supported Models 27
- Supported Features 28
- AT-StackXG Stacking Module 29
- Management Interfaces 30
- Management Access Methods 30
- Enhanced Stacking 31
- Stack Topology 32
- Discovery Process 34
- Master and Member Switches 35
- Active Configuration File 36
- Module ID Numbers 38
- Dynamic Module 39
- ID Numbers 39
- Port Numbers in Commands 42
- MAC Address Tables 43
- File Systems 43
- Stack IP Address 44
- Powering On a Stack 46
- Chapter 1: Overview 48
- Chapter 2 51
- Data bits: 8 52
- Parity: None 52
- <No System Name> 53
- Remote Telnet Management 54
- Quitting a Management Session 56
- Command Formatting 58
- Redundant Twisted Pair Ports 59
- Basic Command Line Commands 61
- CLEAR SCREEN 62
- LOGOFF, LOGOUT and QUIT 65
- SAVE CONFIGURATION 66
- SET PROMPT 67
- SHOW USER 68
- Stacking Commands 69
- SET STACK 70
- SHOW STACK 72
- Chapter 4: Stacking Commands 74
- Basic Stack Commands 75
- DISABLE TELNET 76
- ENABLE TELNET 77
- RESET SWITCH 79
- RESET SYSTEM 80
- RESTART REBOOT 81
- RESTART SWITCH 82
- SET ASYN 84
- SET DATE 85
- SET PASSWORD MANAGER 86
- SET PASSWORD OPERATOR 87
- SET SWITCH CONSOLETIMER 88
- SET SYSTEM 89
- SET TELNET INSERTNULL 90
- SET TIME 91
- SET USER PASSWORD 92
- SHOW ASYN 93
- SHOW CONFIG DYNAMIC 94
- SHOW CONFIG INFO 96
- SHOW SWITCH 97
- SHOW SYSTEM 100
- SHOW TIME 102
- SNMPv2 and SNMPv2c Commands 103
- ADD SNMP COMMUNITY 104
- Section I: Basic Features 105 105
- CREATE SNMP COMMUNITY 106
- Description 107
- Examples 107
- 108 Section I: Basic Features 108
- DELETE SNMP COMMUNITY 109
- 110 Section I: Basic Features 110
- DESTROY SNMP COMMUNITY 111
- DISABLE SNMP 112
- DISABLE SNMP AUTHENTICATETRAP 113
- DISABLE SNMP COMMUNITY 114
- ENABLE SNMP 115
- ENABLE SNMP AUTHENTICATETRAP 116
- ENABLE SNMP COMMUNITY 117
- SET SNMP COMMUNITY 118
- SHOW SNMP 120
- 122 Section I: Basic Features 122
- Port Parameter Commands 123
- DISABLE SWITCH PORT 124
- DISABLE SWITCH PORT FLOW 125
- ENABLE SWITCH PORT 126
- ENABLE SWITCH PORT FLOW 127
- PURGE SWITCH PORT 128
- RESET SWITCH PORT 129
- SET SWITCH PORT 130
- Equivalent Commands 133
- SET SWITCH PORT FILTERING 134
- SET SWITCH PORT RATELIMITING 137
- SHOW SWITCH PORT 140
- Port Statistics Commands 145
- RESET SWITCH PORT COUNTER 146
- SHOW SWITCH MODULE COUNTER 147
- Dropped Frames 149
- SHOW SWITCH PORT COUNTER 150
- MAC Address Table Commands 151
- ADD SWITCH FDB 152
- DELETE SWITCH FDB 154
- RESET SWITCH FDB 156
- Parameter 157
- Parameters 158
- SHOW SWITCH FDB 159
- Static Port Trunking Commands 163
- Overview 164
- ADD SWITCH TRUNK 166
- CREATE SWITCH TRUNK 168
- DELETE SWITCH TRUNK 170
- DESTROY SWITCH TRUNK 171
- SET SWITCH TRUNK 172
- SHOW SWITCH TRUNK 173
- LACP Port Trunking Commands 175
- ADD LACP PORT 176
- CREATE LACP AGGREGATOR 178
- DELETE LACP PORT 180
- DESTROY LACP AGGREGATOR 181
- DISABLE LACP 182
- ENABLE LACP 183
- SET LACP AGGREGATOR 184
- SET LACP SYSPRIORITY 186
- SET LACP STATE 187
- SHOW LACP 188
- Port Mirroring Commands 191
- SET SWITCH MIRROR 193
- SET SWITCH PORT MIRROR 194
- SHOW SWITCH MIRROR 195
- Advanced Operations 197
- File System Commands 199
- CREATE CONFIG 203
- DELETE FILE 204
- FORMAT DEVICE 205
- SET CFLASH DIR 208
- SET CONFIG 209
- SHOW CFLASH 211
- SHOW CONFIG 212
- SHOW FILE 213
- SHOW FLASH 214
- Chapter 14 215
- LOAD METHOD=LOCAL 216
- LOAD METHOD=TFTP 218
- LOAD METHOD=XMODEM 223
- UPLOAD METHOD=LOCAL 227
- UPLOAD METHOD=TFTP 229
- UPLOAD METHOD=XMODEM 232
- Chapter 15 235
- ADD LOG OUTPUT 236
- CREATE LOG OUTPUT 238
- DESTROY LOG OUTPUT 242
- DISABLE LOG 243
- DISABLE LOG OUTPUT 244
- ENABLE LOG 245
- ENABLE LOG OUTPUT 246
- PURGE LOG 247
- SAVE LOG 248
- SET LOG FULLACTION 250
- SET LOG OUTPUT 251
- SHOW LOG 254
- SHOW LOG OUTPUT 259
- SHOW LOG STATUS 261
- Chapter 16 263
- Snooping Protocol 267
- IGMP Snooping Commands 269
- DISABLE IGMPSNOOPING 270
- ENABLE IGMPSNOOPING 271
- SET IP IGMP 272
- SHOW IGMPSNOOPING 275
- Equivalent Command 276
- SHOW IP IGMP 277
- Section IV 281
- SNMPv3 Commands 283
- =password 285
- CREATE SNMPV3 ACCESS 287
- Section IV: SNMPv3 289 289
- CREATE SNMPV3 COMMUNITY 290
- Section IV: SNMPv3 291 291
- CREATE SNMPV3 GROUP 292
- Section IV: SNMPv3 293 293
- CREATE SNMPV3 NOTIFY 294
- Section IV: SNMPv3 295 295
- CREATE SNMPV3 TARGETADDR 296
- CREATE SNMPV3 TARGETPARAMS 298
- CREATE SNMPV3 VIEW 300
- Section IV: SNMPv3 301 301
- DELETE SNMPV3 USER 302
- DESTROY SNMPv3 ACCESS 303
- Chapter 18: SNMPv3 Commands 304
- 304 Section IV: SNMPv3 304
- DESTROY SNMPv3 COMMUNITY 305
- DESTROY SNMPv3 GROUP 306
- DESTROY SNMPv3 NOTIFY 307
- DESTROY SNMPv3 TARGETADDR 308
- DESTROY SNMPv3 TARGETPARMS 309
- DESTROY SNMPV3 VIEW 310
- PURGE SNMPV3 ACCESS 311
- PURGE SNMPV3 COMMUNITY 312
- PURGE SNMPV3 NOTIFY 313
- PURGE SNMPV3 TARGETADDR 314
- PURGE SNMPV3 VIEW 315
- SET SNMPV3 ACCESS 316
- SET SNMPV3 COMMUNITY 318
- Section IV: SNMPv3 319 319
- SET SNMPV3 GROUP 320
- Section IV: SNMPv3 321 321
- SET SNMPV3 NOTIFY 322
- Section IV: SNMPv3 323 323
- SET SNMPV3 TARGETADDR 324
- SET SNMPV3 TARGETPARAMS 326
- SET SNMPV3 VIEW 330
- Section IV: SNMPv3 331 331
- SHOW SNMPV3 ACCESS 332
- SHOW SNMPV3 COMMUNITY 333
- SHOW SNMPv3 GROUP 334
- SHOW SNMPV3 NOTIFY 335
- SHOW SNMPV3 TARGETADDR 336
- SHOW SNMPV3 TARGETPARAMS 337
- SHOW SNMPV3 USER 338
- SHOW SNMPV3 VIEW 339
- 340 Section IV: SNMPv3 340
- Spanning Tree Protocols 341
- Chapter 19 343
- ACTIVATE STP 344
- DISABLE STP 345
- ENABLE STP 346
- PURGE STP 347
- SET STP PORT 351
- SET SWITCH MULTICASTMODE 353
- SHOW STP 355
- Commands 357
- ACTIVATE RSTP 358
- DISABLE RSTP 359
- ENABLE RSTP 360
- PURGE RSTP 361
- SET RSTP 362
- SET RSTP PORT 365
- Port Speed Port Cost 366
- 10 Mbps 20,000 366
- 100 Mbps 20,000 366
- 1000 Mbps 2,000 366
- SHOW RSTP 368
- Virtual LANs 371
- 372 Section VI: Virtual LANs 372
- Port-based and Tagged VLAN 373
- ADD VLAN 374
- CREATE VLAN 376
- DELETE VLAN 379
- Section VI: Virtual LANs 381 381
- DESTROY VLAN 382
- SET SWITCH INFILTERING 383
- SET VLAN 384
- SHOW VLAN 385
- Internet Protocol Routing 387
- Routing Commands 389
- ADD IP ARP 390
- ADD IP INTERFACE 392
- ADD IP ROUTE 394
- DELETE IP ARP 396
- DELETE IP INTERFACE 397
- DELETE IP ROUTE 398
- PURGE IP 399
- SET IP ARP 400
- IP address 149.124.85.14: 401
- SET IP ARP TIMEOUT 402
- SET IP INTERFACE 403
- SET IP LOCAL INTERFACE 405
- SET IP ROUTE 406
- SHOW IP ARP 408
- SHOW IP COUNTER 410
- SHOW IP INTERFACE 412
- SHOW IP ROUTE 414
- Port Security 419
- Control Commands 421
- DISABLE PORTACCESS 422
- DISABLE RADIUSACCOUNTING 423
- ENABLE PORTACCESS 424
- ENABLE RADIUSACCOUNTING 425
- 4.12 and 4.15: 434
- SET RADIUSACCOUNTING 437
- SHOW PORTACCESS 439
- SHOW PORTACCESS 441
- SHOW RADIUSACCOUNTING 444
- RADIUS accounting: 445
- RADIUS Commands 447
- ADD RADIUSSERVER 448
- DELETE RADIUSSERVER 450
- PURGE AUTHENTICATION 451
- SET AUTHENTICATION 452
- SHOW AUTHENTICATION 453
- Chapter 24: RADIUS Commands 454
- Management Security 455
- Web Server Commands 457
- DISABLE HTTP SERVER 458
- ENABLE HTTP SERVER 459
- PURGE HTTP SERVER 460
- SHOW HTTP SERVER 461
- Numerics 463
Související produkty a manuály pro Počítačový hardware Allied-telesis AT-S63
(13 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce