Allied-telesis AT-FS202SC/FS4 Uživatelský manuál

AT-FS201AT-FS202AT-FS202SC/FS1AT-FS202SC/FS2AT-FS202SC/FS3AT-FS202SC/FS4Fast Ethernet SwitchesInstallation GuidePN 613-10761-00 Rev C

Welcome to Allied TelesynxFor Sales or Corporate InformationYou can contact Allied Telesyn for sales or corporate information at the location listed b

1Chapter 1DescriptionThe AT-FS20x and AT-FS202SC/FSx Series Fast Ethernet Switches include the following models:The AT-FS20x and AT-FS202SC/FSx Series

Description2Figure 1 illustrates the front panel of an AT-FS20x Series Switch.Figure 1 AT-FS20x Series Front Panel (AT-FS202 Model)Figure 2 illustrat

AT-FS20x and AT-FS202SC/FSx Series Installation Guide3Table 1 lists the maximum operating distances for the switches.Table 1 Maximum Operating Distan

Description4❑ Store and forward switching mode❑ Automatic address learning and aging❑ IEEE 802.3u compliant auto-negotiation❑ For use on a desktop or

AT-FS20x and AT-FS202SC/FSx Series Installation Guide5Twisted Pair PortThe AT-FS20x and AT-FS202SC/FSx Series Switches have one 10/100Base-TX twisted

Description6To connect two 10 Mbps or 100 Mbps network devices together that have dissimilar port wiring configurations, such as MDI to MDI-X, you wou

AT-FS20x and AT-FS202SC/FSx Series Installation Guide7DIP SwitchesThe DIP switches are used to manually configure the operating characteristics of the

Description8Network TopologiesFigure 4 illustrates a topology using one AT-FS201 switch to interconnect two small networks of stackable hubs. Network

9Chapter 2Installing the SwitchThis chapter explains how to install an AT-FS20x or AT-FS202SC/FSx Series Switch. These switches can be installed on a

Copyright  2001 Allied Telesyn International Corp.960 Stewart Drive, Suite B, Sunnyvale CA 94086 USAAll rights reserved. No part of this publication

Installing the Switch10Planning the InstallationBe sure to observe the following guidelines when planning the installation of your switch.❑ The end-no

AT-FS20x and AT-FS202SC/FSx Series Installation Guide11NoteRefer to “Fiber Optic Port Specifications” on page 18 for additional information on the fib

Installing the Switch12Selecting a SiteBe sure to observe the following guidelines when selecting a site for your switch.❑ Select a site that is dust-

AT-FS20x and AT-FS202SC/FSx Series Installation Guide133. Configure the DIP switches. Refer to Figure 3 on page 2 for the location of the DIP switches

Installing the Switch145. Place the switch on a secure, level surface, leaving ample space around the unit for ventilation.6. Plug the AC/DC power ada

15Chapter 3TroubleshootingFollow the guidelines below to test and troubleshoot the installation in the event a problem occurs.NoteWhenever the speed a

Troubleshooting16If the LNK/ACT LED for the fiber optic port is OFF, do the following:❑ Verify that the end-node connected to the port is ON and is op

17Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H10.5 cm x 9.5 cm x 2.5 cm (4.12 in x 3.75 in x 1.0 in)Weight: 294 g (10.4 oz)Temperat

18Immunity Conforms to EN55024 immunity standardEMI/RFI Meets all applicable requirements for emissionsincluding but not limited to FCC Class A, ICCla

AT-FS20x and AT-FS202SC/FSx Series Installation Guide19Table 8 Fiber Optic ReceiverTable 9 Fiber Optic DatalinkModelFiber Type11. MMF = Multimode Fi

iiiSafety WarningsStandards: This product meets the following standards.RFI Emission EN55022 Class A $ 1Warning: In a domestic environment this produc

20Table 10 Fiber Optic Loss Specification (Benchmark)Pinout AssignmentsFigure 1 shows the pin assignments of the RJ-45 connector.Figure 1 RJ-45 Pin

21Appendix BElectrical Safety and Installation RequirementsImportant: This appendix contains multiple-language translations for the safety statements

22Standards: This product meets the following standards.$ 1 RFI Emission EN55022 Class A$ 2 Warning: In a domestic environment this product may cause

AT-FS20x and AT-FS202SC/FSx Series Installation Guide23Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.$ 1Hochfrequenzstörun

24Sikkerhed$ 10 Fare Under UvejrFare: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.$ 11 VENTILATIONSÅBNINGERNE MÅ IKKE BLOKERE

AT-FS20x and AT-FS202SC/FSx Series Installation Guide25Normes: ce produit est conforme aux normes de suivantes.$ 1 Emission d'interférences radio

26$ 12 Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan sovittimesta.Europe - EUKäytä TÜV-lisenssillä valmistettua verkkosovitinta, jon

AT-FS20x and AT-FS202SC/FSx Series Installation Guide27Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.$ 1 RFI stråling E

28Europe - EUUse um adaptador de corrente alternada com saída DC de 12V e 500mA em conformidade com as especificações da TÜV.$ 13 Temperatura De Func

AT-FS20x and AT-FS202SC/FSx Series Installation Guide29Standarder: Denna produkt uppfyller följande standarder.$ 1Radiostörning EN55022 Klass A$ 2 Va

Safety WarningsivImportant: L'annexe B contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous voye

31Appendix CTechnical Support Fax OrderName _________________________________________________________________Company__________________________________

vTable of ContentsSafety Warnings ...iiiWelcome to Allied Te

Table of ContentsviChapter 3Troubleshooting ...15Appendix ATe

viiThis guide contains instructions on how to install the AT-FS20x and AT-FS202SC/FSx Series Fast Ethernet Switches.Where to Find Web-based GuidesThe

Welcome to Allied TelesynviiiContacting Allied Telesyn Technical SupportYou can contact Allied Telesyn technical support online or by telephone, fax,

AT-FS20x and AT-FS202SC/FSx Series Installation GuideixTechnical Support E-mail AddressesUnited States and [email protected] America, M