Allied-telesis AT-S84 Uživatelský manuál Strana 158
- Strana / 326
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 11: Rapid Spanning Tree Protocol (RSTP)
158 Section II: Menus Interface
Configuring STP Compatibility
Choosing an RSTP protocol version allows you to determine if the switch
ports will operate in RSTP-only mode or are STP-compatible. This setting
applies to all of the ports; you cannot set this on a per-port basis.
To configure the STP compatibility, perform the following procedure:
1. From the Main Menu, type B to select Basic Switch Configuration.
The Basic Switch Configuration Menu is shown in Figure 4 on page
32.
2. From the Basic Switch Configuration Menu, type S to select Rapid
Spanning Tree Configuration.
The Rapid Spanning Tree Configuration Menu is shown in Figure 42
on page 153.
3. Type V to select Set RSTP Protocol Version.
The following prompt is displayed:
Set RSTP protocol version (S/R)>
4. Type S to make the ports STP-compatible, or R to make the ports
operate only in RSTP mode.
- Management 1
- Software 1
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 15
- Overview 17
- Management Overview 18
- Local Connection 19
- Remote Connection 20
- Management Access Level 21
- Chapter 1: Overview 22
- Using the Menus Interface 23
- Interface 25
- Enter system name> 37
- Enter system location> 37
- Enter system contact> 37
- Enter current password> 40
- Enter old password> 40
- Enter new password> 40
- Retype new password> 41
- Viewing Switch Information 47
- Rebooting the Switch 50
- Enter new timeout value> 53
- Figure 14. Ping Results 54
- Chapter 4 59
- SNMP Overview 60
- Default SNMP 61
- Community 61
- Chapter 4: SNMP 62
- Enabling Authentication Traps 63
- Enter read community name> 64
- Modifying a Trap 66
- Receiver 66
- Deleting a Trap 67
- Chapter 5: Port Configuration 70
- Enabling or Disabling a Port 72
- Enter new mode for port 73
- (a/h/H/F/f/T)> 73
- (E/D)> 75
- Port Trunking Overview 82
- LACP Trunks 84
- LACP Port 85
- Priority 85
- Parameter 85
- Modifying a Port 90
- Enter trunk group number> 96
- Set trunk group 96
- status (A/P/M/D)> 96
- Port Mirroring Overview 98
- Chapter 7: Port Mirroring 100
- Virtual LANs and GVRP 103
- VLAN Features 104
- VLAN Overview 106
- Incoming Frames 107
- Tagged Port Members 107
- Untagged Port Members 107
- Outgoing Frames 108
- AT-9000/24 109
- Tagged VLAN 111
- Working with VLANS 113
- Configuring the 116
- Port PVID 116
- Displaying the 117
- Changing the VLAN Name 119
- Enter VLAN ID > 120
- Resetting to the 121
- Default VLAN 121
- Enabling or 123
- Disabling GVRP 123
- Quality of Service (QoS) 125
- QoS Overview 126
- Configuring CoS 132
- Enter queue for trunk group 135
- >> 135
- IGMP Snooping 137
- IGMP Snooping Overview 138
- Configuring IGMP 140
- Enter age out time> 141
- Viewing the Multicast Groups 142
- Chapter 10: IGMP Snooping 144
- Chapter 11 145
- RSTP Overview 146
- Path Costs and Port Costs 147
- Port Priority 148
- Point-to-Point and Edge Ports 149
- Point-to-Point Ports 150
- (Full-duplex Mode) 150
- Mixed STP and 151
- RSTP Networks 151
- Rapid Spanning 152
- Tree and VLANs 152
- Enabling or Disabling RSTP 153
- Enter bridge priority> 156
- Enter bridge hello time> 156
- Enter bridge maximum age> 157
- Configuring STP Compatibility 158
- Basic RSTP Port 159
- Settings 159
- Advanced RSTP 161
- Port Settings 161
- Displaying the RSTP Topology 164
- 802.1x Network Access Control 167
- Authentication 169
- Authenticator 169
- Network Access 171
- Guidelines 171
- Switch A 173
- Switch B 173
- Enter port number> 175
- Enter NAS ID > 175
- Chapter 13 179
- RADIUS Overview 180
- Configuring the RADIUS Server 181
- Broadcast Storm Control 185
- Working With System Files 189
- Enter file name> 192
- Enter retry count> 192
- Download file? (Y/N)> 192
- Uploading the 193
- Configuration 193
- Downloading a 195
- Section II 197
- Chapter 16 199
- Switch’s IP Address 200
- Web Browser Tools 203
- Basic Switch Parameters 205
- 3. Click Apply 210
- Server and SNMP settings 212
- Configuring SNTP 216
- Viewing System Information 217
- Rebooting a Switch 219
- Pinging a Remote System 220
- Viewing the System Log 222
- Port Configuration 225
- Displaying Port Statistics 232
- Chapter 19 235
- Chapter 19: SNMP 236
- Working with Trap Receivers 238
- Port Trunking 239
- Setting Up a Port Trunk 240
- Disabling a Port 241
- Setting Up an LACP Trunk 242
- Verifying the 243
- LACP Group 243
- Disabling an 244
- LACP Trunk 244
- Port Mirroring 245
- Configuring Port Mirroring 246
- Disabling Port Mirroring 247
- Chapter 21: Port Mirroring 248
- Virtual LANs 249
- Creating a VLAN 250
- Chapter 22: Virtual LANs 252
- Displaying the VLANs 255
- Modifying a VLAN 256
- Deleting a VLAN 258
- Deleting All VLANs 259
- Enabling or Disabling GVRP 260
- Chapter 24 267
- Chapter 24: IGMP 270
- Chapter 25 271
- Basic RSTP Configuration 272
- Chapter 25: RSTP 276
- Viewing the RSTP Topology 278
- Chapter 27 285
- Configuring the RADIUS Client 286
- Working with System Files 289
- Section III 295
- Formatting 299
- Conventions 299
- User EXEC 300
- Command Mode 300
- Privileged EXEC 301
- 302 Section I: Basic Features 302
- Port Mirroring Example 304
- VLAN Example 306
- Section I: Basic Features 307 307
- Command Formatting 308
- Section I: Basic Features 309 309
- 310 Section I: Basic Features 310
- AT-S84 Default Settings 311
- Basic Switch Default Settings 312
- SNMP Default Settings 314
- Quality of Service 316
- RSTP Default Settings 318
- Settings Default 320
- Server IP Address 0.0.0.0 320
- Response Time 10 seconds 320
- Maximum Retransmissions 3 320
- Threshold Low 321
- 322 Section I: Basic Features 322
Související produkty a manuály pro Počítačový hardware Allied-telesis AT-S84
(514 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce